background image

 

 

 

 

 

Instructions 

1005101738 

ENVI to NURO  

Date: 12/19/2017 

Revision A 

NURO Conversion Instructions 

MACH C1500-C2000H 

 

 

 

 

 

 

 

Indicates a potentially hazardous situation which, if not avoided, 

may

 result in minor or moderate injury.  It may also 

be used to alert against unsafe practices. 

 

 

 

 

Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.  This signal 

word is to be limited to the most extreme situations. 

 

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

 

N

OTICE

!

 

Each safety device must be maintained and checked per the recommended schedule.  Refer to Section 6 in 
the O&M Manual for more information. 

S

AFETY 

F

EATURES

 

It is the responsibility of the customer to ensure external safety provisions, such as but not limited to: 
guards, safety labels, safety controls, interlocks, lockout devices are in place and operable.  

 

S

AFETY 

L

ABELS

 

The following words are used in this manual to denote the degree of seriousness of the individual hazards.  

N

OTICE

/N

OTE 

-

 

N

OTICE

 

Is the preferred signal word to address practices not related to personal injury.  The safety alert symbol is 
not used with this signal word.   

Содержание MACH C1500





















Отзывы: