Align Flanges
Optional 2nd Remote UV Light
Installation Instructions
The optional Remote UV Light works with
the PCO system for enhanced disinfection,
reduced system maintenance, and improved
indoor air quality.
2
Air Handler Interior Surface Installation
1.
Determine the optimal position
for placement of the
UV lamp.
2.
Use a utility knife to cut a slit in the insulation
on the interior surface.
3.
Place the magnetic
“Z” bracket
directly on the
metal surface or remove the magnet and hard-
mount the bracket using the
self-tapping
screws
provided. Use foil tape to close the cut
in the insulation.
4.
Use plastic
quick-nuts
to attach the
UV lamp
to the
“Z” bracket
as shown.
IMPORTANT!
• PCO Dual lamps are wired in series - both must be connected for lamps to light
• Only qualified technicians should install this product
• Install in accordance with relevant building codes
• Read instructions carefully including safety warnings
2.
3.
4.
P
3
Coil “A” plate or Duct Installation
1.
Snap the
“Z” bracket
apart by
bending.
2.
Drill a 1” hole in the "A"-plate
or duct then attach the smaller
piece of the bracket using the
self-tapping screws
.
3.
Insert the
UV lamp
into the hole
then use the plastic
quick-nuts
to attach the
UV lamp
to the
“Z” bracket
as shown.
1.
2.
3.
P
1
Installation Notes
Before installing the Remote UV Light it is necessary to
determine the optimal mounting location inside the air
system. First, look for the area with the heaviest mold
growth. Also consider a location that will allow the
germicidal UV light to shine on the greatest surface area.
Some typical mounting locations:
A
Supply-side duct
B
At the blower
C
Across top of coils
D
Coil face
E
Coil "A" plate
F
Return-side duct
Important:
some materials inside the air system (including
filter media, flex duct, wiring etc.) may not be UV light resistant.
Use the optional UV shield (part #TUV-SHIELD-LPC) or cover
the materials with reflective tape.
WARNING
PROTECT EYES FROM UV LIGHT
TURN OFF UNIT OR DISCONNECT
BEFORE SERVICING
Mounting Options
A
B
C
D
D
E
F
Electronic
Power Supply
H
or
I
Optional 2nd
UV Lamp
N
O
5
Remote UV Lamp Connection
1.
When all the other components are properly installed connect the UV Lamp
cable to the
PCO
Power supply cable.
2.
Make sure the flanges are aligned and then push the connectors firmly
together. A tight connection ensures a proper water-resistant seal.
2.
1.
7
Lamp Replacement
The germicidal UV lamp in the Remote UV Light needs to be replaced periodically. A
TUVL-115P lamp should be replaced every year. The TUVL-215P should be replaced
every 2 years. Note: UV lamps will continue to emit visible light but lose germicidal
effectiveness over time. You can upgrade to a 2 year with your existing power supply.
TUVL-115P
(1 Year)
TUVL-215P
(2 Year)
CAUTION!
UV lamps contain small amounts of mercury - dispose of lamps in accordance with
local environmental regulations. For more information visit www.lamprecycle.org
4
Remote UV Light Configuration
IMPORTANT!
Only the Patriot PCO Dual model has the
electrical capacity and attached cable for the optional
Remote UV Light. Simply connect the lamp lead to the
power cable on the left side of the Patriot PCO Power Unit.
To add a second UV light to an existing Patriot PCO system
that is not a Dual model install a separate Patriot UV system.
6
Sight Glass Installation
1. Find a suitable location on the outside
of the duct-work near the UV Lamp
installation and apply the warning/lamp
replacement sticker.
2. Drill a ½” hole through the orange circle
on the sticker. Press the UV safety viewport
into hole.
3. Turn on the power and use the sight glass to
confirm that the UV Lamp is operating.
