10
The display stays on for approximately 30 seconds after a button press. After 30 seconds with no
button press,
the
blue backlight
shuts off
first, and if no button press with another
five minutes, the
Note: The battery indicator will flash
Indicates Transmitter is ready to pair
seconds to dispaly and begin pairing.
Transmitter LED Indicator Light – Function and Response
Button
Button Function
Transmitter Indicator Light Response
Tone (
yellow
)
Delivers audible tone to collar
Red
LED on for length of button press
Stimulation
(
red
)
Delivers stimulation to collar based on
current level shown on Digital Display
(stimulation will time-out if pressed
continuously for 1
0
seconds or longer
and will reset after release)
Red LED on for length of button press
Delivers
vibration
to
collar
based on
current
level
shown
on
Digital
Display
(
vibration w
ill also time-out after
button is held for 1
0
continuous seconds)
Red LED on for length of button press
+ and -
Buttons held
simultaneously
Transmits Pairing command to
Receiver
Collar when P is visible on
Digital Display
or
Sending signal to
Red
LED on for length of button press
Prepare the Receiver Collar
To Insert and Remove the Batteries
2.
Place
the
Collar
in
the
right
place
and
3.
Use
the
Test
Light
and
install
Replacement batteries (
) can be found at many retailers.
Or
please
c
ontact
us
for
1
.
5-volt, LR03
AAA
Risk of explosion if battery is replaced by an incorrect type. Do not short circuit, mix
old and new batteries, dispose of in fire, or expose to water. When batteries are stored
or disposed, they must be protected from shorting. Dispose of used batteries properly.
1. Press and hold the On/Off Button until the Green LED light comes on.
(This takes approximately one second.)
2. Release the On/Off Button.
In normal mode, the Green LED will flash once every 5 seconds, indicating the Receiver
2. Release the On/Off Button. Note: To extend the life of the batteries, turn the Receiver Collar
off when it is not in use.
Important: If the Receiver Collar is left on continuously, the maximum battery life will be
two weeks.
Step
2
display shuts off and the
Transmitter goes into battery conservation mode. Pressing any button
Transmitter Digital Display
will turn the display back on. The symbols on the display are explained below.
Indicate
s stimulation
/vibration
levels
lower
middle part.
Indicates
the active dog receiver
and
next to
the battery
corner
s
indicator.
Vibration
(blue)
1
.
Remove
the
Battery
Cover
and
install
two (2), 1
.
5-volt (LR03
AAA) batteries with
correct
positive (+)
negative
(-)
sides
.
And
replace
the
Battery
Cover
to
the Receiver Collar.
(
2A
)
ranging from 1-
16
, and appears in the
Receiver Collar. Press button
for 3
appears in the
upper left and
right
Indicates
battery
’
s
power
level
.
every
second to indicate low battery.
Stimulation
mode
symbol
indicate
Stimulation
button
press
on
Vibration
mode
symbol
indicate
Vibration
button
press
on
transmitter
.
transmitter
.
Tone mode
symbol
indicate Tone
button
press
on
transmitter
.
with
Indicates sending signal to
Receiver Collar when and
buttons are
held
simultaneously
.
cover
the
Securing
Pads
.(
)
2B
the Contact
Points (
).
2C
direct purchase.
DO NOT OVER-TIGHTEN THE CONTACT
POINTS WHEN USING THE TEST LIGHT.
To turn Receiver Collar On
To turn Receiver Collar Off
1. Press and hold the On/Off Button
until the Red
LED light shuts off.
(This takes approximately three seconds.)
Collar is on and ready to receive a signal from the Handheld Transmitter.
1
1
2
A
2B
2C
Receiver Collar where Green LED
light
flashes every second as response.
