background image

Collar Fitting

Please fit the collar properly so that the Contact Points press firmly 
against the dog’s skin. When properly fitted, you should be able to put 
a finger in between the Receiver Collar and dog’s neck. 

 

Caution:

 1.do not shave the pet’s neck as this 

may increase the risk of skin irritation.
2.the collar should not be worn for more than 12 
hours per day. Or it may cause skin irritation.

Too tight:

 it may cause dog’s to breathe hard.

Too loose: 

the Receiver Collar will move around the dog’s neck, the 

Contact Points may hurt the dog’s skin.

3.  Press the Shock Button and the Test Lamp will be lighted. It will be
   

Use the Test Lamp to tighten or loosen the Contact Points when 
prepare  the Receiver Collar.

As a Screw Driver

Pair the Remote and the Receiver Collar

1. Use the         switch on the Remote to select Dog 1 .
2. With the Remote turned on and the Receiver Collar turned off, press 
    and hold the ON/OFF Button on the Receiver Collar for 4-5 seconds.
3. The Red & Green LED will blink for about 10 seconds indicating that  
    it is ready for pairing.
4. Press and hold Tone Button and Vibration Button at the same time 
    for 2-3 seconds, the Green Led on the Receiver  Collar will blink 
    for 5 times indicating successful pairing.

1.  Use the        Button on the Remote to select Dog 2. Then follow 
    the above pairing steps from 2-4.

Dog Training

Find the Best Shock Level for Your Pet

Device Information

Battery Type

Battery Life(typical use)

Remote Waterproof Rating
Receiver Waterproof Rating
Operating temperature range
Wireless Power
Wireless Range

Product Specification

IEC 60529 IPX7, waterproof

20dBm(100mW)

300m(984 feet)

From 0-40

(from 32-104

)

Non-Waterproof(Keep away from water)

Remote: 27 days
Receiver: 11 days

Rechargeable, lithium polymer battery

lighter accordingly with the Shock Level increasing.

8

9

10

11

12

13

How long can I 
continuously deliver 
Vibration/Shock to 
my pet? 

The maximum amount of time you can press 
the Vibration/Shock Button and deliver 
Vibration/Shock to your pet continuously is 
10 seconds. After this, there’s a time-out an 
Vibration/Shock cannot be delivered for 5 
seconds. After the 5 second time-out period, 
Button can be pressed and Vibration/Shock 
can be delivered again.

Troubleshooting Guide

Make sure the Receiver Collar has been turned on.
If your range has reduced from the first time you 
used the Remote Training Collar, the battery(s) 
may be low in either the Remote or Receiver Collar. 

 

My pet does not 
respond when I 
press a button.

The Receiver 
Collar will not 
turn on.

Make sure the Receiver Collar is on.

 

If the Indicator Light does not come on when any 

button is pressed on the remote, ensure that the 

batteries are charged properly.

If the first two solutions did not resolve your problem, 

Refer to 

“Pair the Remote and the Receiver Collar”

Make sure the Receiver Collar has been charged. 

For the initial charge, be sure to charge it for 4 

hours. Subsequent charges only take 2-3 hours.

Terrain, weather, vegetation, transmission from 
other radio devices and many other factors can 
impact the amount of range you have with the unit.
Test the Receiver Collar. Refer to “How to use the  
Test Lamp” for details.
Increase the Shock Level. Refer to “Find the Best 
Shock Level for Your Pet” for more information.
Make sure the Receiver Collar’s Contact Points 
are placed snugly against your pet’s skin. Refer to 

Collar Fitting” for more information.  

The Receiver 
Collar is not 
responding to 
the Remote.

Others

Frequently Asked Questions

Will I get exactly 984 feet 
of range with the Remote 
Training Collar?

Is the Vibration/Shock 
safe for my pet?

How old does my pet have 
to be before using the 
Remote Training Collar?

Once my pet is trained and 
has been obeying my 
commands, will he have to 
continue to wear the 
Receiver Collar?
Is the Receiver Collar 
waterproof?

While the Vibration/Shock is unpleasant, 
it is harmless to your

 

pet. Electronic 

training devices require interaction and 
training from the owner to achieve 
desired results. 

Your pet should be able to recognize 
basic obedience commands such as 
“Sit” or “Stay”.Pets should be at least 6 
months old before using the Training 
Collar.

Probably not. You may need to reinforce 
training with the Receiver Collar from 
time to time.

Yes.

 

The range of the Remote Training will 
vary according to terrain, weather, 
vegetation, as well as transmission 
from other radio devices. Refer to “To 
maximize the distance” for tips on 
maximizing your range.

The unit comes with Up and Down buttons to control the Shock Level, 
with Level 1 being the lowest level and Level 16 being the highest. The 
level of Shock best suited for your dog depends on your dog’s 
temperament and threshold for Shock. Always start at the lowest level 
and work your way up.

 

The appropriate level can be found when the dog 

responds to the Shock with a mild reaction, 

such as a flick of the ear, a 

lick of the lips, a tensing of the neck muscles etc. The Shock Level may 
vary depending on the training situation.

 When highly distracted, dog’s 

will require a higher level of Shock.

The unit need to be charged under any of below situations

1. The indicator light on the Receiver Collar is emitting a red color every 
      seconds or flashes rapidly.

4

2. The 3 bar indicator on the Remote LCD shows just 1 bar. 
3. The indicator light on the Remote or Receiver Collar will not come on. 
4. The indicator light on the Remote or Receiver Collar comes on 
    momentarily when any of the Mode Buttons is pressed. 

Pairing a Second Collar with the Remote

Warranty and repair information

1-Year Limited Lifetime Warranty

The original purchaser for this unit is provided with 1-

YEAR

 

WARRANTY

.

The warranty begins from the date of purchase. For the first year, 
coverage is for both Parts and Labor on warranty repair services.

Accessories such as straps and batteries are covered for the first year 
only. After the first year, the Limited Lifetime Warranty covers Parts 
only and does not cover Labor Fees and Accessories. All shipping fees 
incurred, the cost of Accessories after the first year, and Labor fees 
associated with out of warranty repair work, are the customer’s 
responsibility. Labor fees will be variable depending on the extent of 
the work required. The Limited Lifetime Warranty expires 5 years after 
a model is discontinued from production.
To Qualify for the Warranty

All products must provided a proof of purchase is required to initiate 
repair work under warranty. We strongly recommend keeping the 
original receipt. If a proof of purchase is not available at the time of 
service, we will estimate the age of unit by the serial number. Serial 
number estimates can differ from the actual purchase date. A serial 
number estimate is the only method of determining an approximate 
date of purchase without a proof of purchase.

Not Covered Under Warranty

We DO NOT offer warranty for products that have been bought 

secondhand or as a resold product. We DO NOT replace defective 

units or provide refunds for products purchased from us after 30 days 

from the date of purchase. Issues of replacement and refunds on units 

purchased less than 30 days from an authorized dealer must be 

addressed to the dealer directly. If the products purchased from an 

authorized dealer are after 30 days from the date of purchase, please 

send the units to us for service and repair. We DO NOT cover the cost of 

repairs and replacements due to misuse by the owner or dog, improper 

maintenance, and/or lost units. Any water damage on the Water 

Resistant remote and the Water Resistant Receiver of our product 

Note: 

This equipment has been tested and found to comply with the 

limits for a Class B digital device, pursuant to part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment 
generates uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause 

Procedure for Repair Work

series will not be covered. All replacement costs for either the remote 
or receiver will be the owner’s responsibility. The warranty is void if the 
unit has been altered or an unauthorized person has damaged the unit 
while attempting repair work. We reserve the right to retain and discard 
any parts or accessories that have been found damaged upon 
replacement and repair.

If the unit is malfunctioning, please refer to the “Troubleshooting 
Guide” in the quick start before sending it back for Service. The cost of 
shipping products under warranty back is the customer’s responsibility. 
We are not responsible for units damaged or lost in transition. We are 
not responsible for loss of training time or inconvenience while the unit 
is in for repair work. We do not provide loaner units or any form of 
compensation during the repair period. A copy of the sales receipt 
showing the purchase date may be required before warranty work is 
initiated. Please include a brief explanation outlining the problem and 
include your name, address, city/state/zip code, daytime phone 
number, evening phone number, and email address. 

Compliance
FCC - USA

This device complies with part 15 of the FCC Rules. Operation is 
subjectto the following two conditions: 
(1) This device may not cause harmful interference.
(2) this device must  accept any interference received, including 
interference that may cause undesired operation.

-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on,  
the user is encouraged   to try to correct the interference by one or more 
of the following measures: 
-Reorient or relocate the receiving antenna.

CAUTION: Modification or changes to this equipment not expressly 
approved by manufacturer

 

 may void the user”s 

authority to operate the equipment.

Selecting The Contact Points and The Contact
spring sheet

For the best results, select the correct Contact Points based on your 
dog’s coat.

 You can use the Contact point separately,
 or use the Contact point and spring at the same time.
   

04

RoHS

MADE IN CHINA

Shenzhen Patpet Technology Co.,Ltd
Add: No.1 Qinhui Road, Gushu Community,
Xixiang Street, Baoan District, Shenzhen, China

 

The R&D of Dog Remote Training Collar

https://patpet.com/

[email protected]
@PatpetDogCollar

8

9

10

11

12

13

14

Содержание p-collar 650















Отзывы: