Thank you for specifying the PATLITE for your application.
Please read these instructions carefully before you perform installation, maintenance and repair.
Store this manual carefully for easy reference.
If you have any questions about this product, please contact PATLITE Corporation.
●
Make sure the power is OFF before wiring ,repairing , or replacing parts to avoid a short-circuit , electric shock or burn.
●
Do not use this product with damaged lens damaged or removed , or without the head cover in order to avoid an electric shock.
●
Do not drop the product. It may damage lenses or other parts.
●
If installing this product requires construction work, please ask a specialist in order to avoid an electric shock, fire, or personal injury.
●
When this product is used for security purposes, it should be inspected daily. In case a malfunction should occur,
it is recommended that you use this product together with other security products.
●
Do not use this product tosupport your weight while climbing onto machine. Mount the product so that it is clear of any moving parts -
such as a machine cover.
●
Concerning replacement parts, such as LED unit, bulb or fuse, be sure to use those specified in this manual.
●
For safety, make sure to connect an external fuse to the power source as shown in the wiring example.
●
Do not touch the electronic components except for the switch that control the frequency of flash.
●
The flashing frequency and the buzzer cycle may become remarkably fast by the noise.
P E S -
□ □ □
■
Rated voltage
24
：
24V AC/DC
100
：
100
Ｖ
AC
120
：
120
Ｖ
AC
200
：
200
Ｖ
AC
230
：
230
Ｖ
AC
Caution
P E W -
□ □ □
B
■
Rated voltage
24
：
24V AC/DC
100
：
100
Ｖ
AC
120
：
120
Ｖ
AC
200
：
200
Ｖ
AC
230
：
230
Ｖ
AC
■
Buzzer
［
PES type
］
［
PEW type
］
INSTRUCTION MANUAL
［
Type:PES/PEW
］
Warning
1. To operate this product safely, please observe the following
2. Model No. Configuration
3. Parts Name and Dimensions
■
Parts Name
B
：
Buzzer
Brank
：
No buzzer
NOTES TO BE OBSERVED FOR SAFE OPERATION
In order to prevent any damage to the user and other personnel or to assets , note the follows:
■
The indications for warning are divided into the following classes according to the degree of danger or
damage incurred when the warning is not taken into consideration and the product is not correctly used.
Warning
Indicates an imminently dangerous condition: failure to follow the instructions may
lead to death or serious injury.
O-ring
(Accessory)
Screws
Nuts (Accessory)
Signal line
Power line
Power line
Signal line
Power line
Signal line
Waterproof sheet
Volume knob
Case
Flash frequency
adjustment Switch
Dome
Caution
Indicates a potentially dangerous condition: failure to follow the instructions may
lead to slight injury or property damage.
－
6
－
■
Dimensions
4. Installation
●
Drill the surface where this product is installed.
●
Fix the product with accessory nuts and washers.
●
With buzzer models, the alarm can be heard best from the front direction.
Therefore make sure the product is facing the correct direction before install it.
(77)
75
●
The Installation must be done where the position has enough strength and less vibration.
●
If the product is installed in an outdoor location, do not install it sideways or upside-down.
●
To clean the dome or the case, use a wet cloth.
(Do not use thinner, benzene, gasoline, oil and any other solvent.)
7mm MAX
Accessory nuts and washers
［
PES type
］
1 Drill the surface where this product
is installed.
(Use a template for easy installation.)
2 Fix the product securely with nuts and
washers.
■
Two points installation case
■
Three points installation case
［
PES type
］
［
PEW type
］
φ
107
φ
82
φ
82
(77)
Length from line exit
13
３－Ｍ４
50
Power line 970
Signal line 870
Power line 970
Signal line 870
Signal line 900
-0
+70
-0
+70
-0
+70
-0
+70
-0
+70
-0
+70
-0
+70
-0
+70
-0
+70
-0
+70
Power line 960
Signal line 860
(Unit
：
mm)
Power line 1000
Power line 960
Signal line 860
Length from hooking line
＞
ABS
＜
■
Side exit for lines
・
Cut four grooves and remove the walls.
・
Use the vinyl tube not to get caught lines between the product and
installation surface.
■
Under exit for lines
・
Install the product after the installation of the
waterproof sheet.
Line
Main body
Waterproof sheet
Line
Main body
［
PEW(-B) type
］
①
Drill the surface which this product is installed. (Use a template A for easy installation.)
②
Put down the waterproof sheet and install the product on it.
(Refer to the figures as follows.)
③
・
The case of two points installation
Fix the product with the accessory nuts and screws.(The case of drill
φ
5)
・
The case of three points installation
Fix the product with the accessory tapping screws.
Grooves
6mm Max.
18
Accessory
screws
Accessory nuts
Waterproof sheet
Waterproof sheet
15
Accesory screws
5mm Max.
－
7
－
(77)
φ
107
75
φ
82
φ
82
(77)
13
50
AC100V
AC200V
AC100V
AC200V
AC100V
・
AC200V
AC/DC24V
AC120V
・
AC230V
AC/DC24V
AC120V
・
AC230V
AC100V
・
AC200V
AC/DC24V・AC120V・AC230V
AC/DC24V・AC120V・AC230V
Caution
