Electric I&O Manual
IM111116 RL:2A AUG 2018
5
REPLACEMENT ELEMENT INSTALLATION
11/32" OUTSIDE NUT
11/32" INSIDE NUT: SNUG TO CERAMIC;
HOLD FIRMLY TO TIGHTEN OUTSIDE NUT
Consult the
label on back of
heater for proper
watts, voltage,
and replacement
element part
number.
Need help?
To order
replacement
elements for your
heating system,
please contact us
via phone or visit
our website.
REPLACEMENT ELEMENTS
[277 & 480 VOLTAGES ALSO AVAILABLE]
PART NUMBER LENGTH
WATTS
VOLTS
FITS
JE-0550-12 16.5" [0.4 m]
500
120
ES-0519-12, EL-0519-12
JE-0551-12 16.5" [0.4 m]
750
120
ES-0719-12, EL-0719-12
JE-0552-12 30" [0.8 m]
1000
120
ES-1033-12, EL-1033-12
JE-0553-12 30" [0.8 m]
1500
120
ES-1533-12, EL-1533-12
JE-0554-20 16-1/2" [0.4 m]
2000
208
ES-2039-20, ES-4039-20/EL-2039-20, EL-4039-20
JE-0555-20 30" [0.8 m]
2500
208
ES-2539-20, ES-5039-20/EL-2539-20, EL-5039-20
JE-0556-20 30" [0.8 m]
3000
208
ES-3061-20, ES-6061-20/EL-3061-20, EL-6061-20
JE-0557-20 36" [0.9 m]
4000
208
ES-4061-20/EL-4061-20
JE-0554-24 36" [0.9 m]
2000
240
ES-2039-24, ES-4039-24/EL-2039-24, EL-4039-24
JE-0555-24 58" [1.5 m]
2500
240
ES-2539-24, ES-5039-24/EL-2539-24, EL-5039-24
JE-0556-24 58" [1.5 m]
3000
240
ES-3061-24, ES-6061-24/EL-3061-24, EL-6061-24
JE-0557-24 58" [1.5 m]
4000
240
ES-4061-24/EL-4061-24
REPLACEMENT PARTS
PART NUMBER
PART DESCRIPTION
QUANTITY
JE-0570-XX
Single Element End Reflector [Set of 2]
1
JE-0571-XX
Dual Element End Reflector [Set of 2]
1
JE-0573-XX, JE-0574-XX, JE-0575-XX
Body Reflector – Fits 33" [0.8 m], 39" [1.0 m], 61-1/4" [1.6 m]
1
JE-0577-XX, JE-0578-XX, JE-0579-XX
Grill Guard – Fits 33" [0.8 m], 39" [1.0 m], 61-1/4" [1.6 m]
1
JE-0581-XX, JE-0582-XX, JE-0583-XX
Lead Wire Set – Fits 33" [0.8 m], 39" [1.0 m], 61-1/4" [1.6 m]*
1
JE-0585-XX
Stainless Steel Mounting Bracket [Set of 2]
1
* Note: Dual Element Heaters require 2 Lead Wire Sets per Heater
Disconnect the power at the breaker.
Remove the grill by grasping it in the middle, flex grill up and lift it off.
Unscrew and remove both end reflectors. Unhook element clips at each end of the heater and remove nuts from
end of element to remove the existing Quartz. Carefully install the new element. Remove one nut from end of the
new element. Install wire by sliding high temperature ring terminal onto element screw and replace nut. Use a thin
11/32" wrench to hold inside nut. Nuts must make a tight connection. Close element clips over tube, reinstall end
reflectors, then snap protective grill back in place.
NOTE: Hold ceramic element firmly while
tightening nut to prevent damage to element.
Nut should be tightened snug. A loose
connection can cause the element to short
or fail prematurely.
