Installation Guide
PATHPORT INSTALL GUIDE-REV7
12/10/18
empty of debris. Inspect the Uno and make sure all components
are securely fastened and that the printed circuit boards are intact.
If the back backbox contains an Ethernet RJ45 female punchdown-
connector, use a male-to-male jumper to connect it to the Uno.
Otherwise, plug the male RJ45 pigtail directly into the connector
on the back of the Uno. Attach the green ground wire to the ground
screw in the backbox.
Gently insert the Uno straight into the backbox and screw it into
place with the long mounting screws provided. Place the cover plate
over the installed Uno and use the two short screws to fasten the
cover plate. Do not over-tighten these screws.
Disconnect all power before proceeding.
Because Pathport eDINs are intended for installation within
enclosures, if you are installing multiple gateways it’s a good idea to
maintain a log of serial numbers. The serial numbers are exposed
when the gateways are discovered in Pathscape which is where they
will be patched. If the devices are easily visible from where you run
Pathscape, use the “Identify” feature, which will blink the blue Identify
LED on the selected gateway.
Securely mount DIN rail (if not already installed in the enclosure).
Hook the upper slots on the back of the plastic extrusion to the DIN
rail and then gently but firmly press on the bottom front corners of
the extrusion to snap the module onto the rail. Do NOT press directly
on the PCB card itself.
Attach the DMX wiring to the terminal strip output connector(s). If
the Pathport eDIN is using an auxiliary power supply, connect the
terminal strip. Observe DC polarity.
Attach the network cable to the RJ45 connector marked Ethernet.
The Pathport is ready to be powered up. Both auxiliary power and
PoE can be connected simultaneously without damaging the Path-
port eDIN.
Pathport 1011’s may be set permanently to a specific DMX universe,
1 through 4, by use of a DIP switch block on the circuit board. If the
system designer has not given specific instructions about this setting,
all switches should be left in the OFF position, and configured with
Pathscape.
The Portable Uno may be powered
using Power-over-Ethernet or a 24VDC
supply with a 2.5mm center-positive
barrel connector.
To attached the hanging bracket
(included), remove the top two
screws from either end of the
portable enclosure (four screws
altogether), position the hang
-
ing bracket over the top of the
enclosure, then use the same screws
to attach the bracket to the enclosure.
The hanging bracket has a 1/2” (12.5mm) hole suitable for a
C-Clamp or other hanger (not included).
The Pathport Touring Edition operates on Power-over-Ethernet
during normal operation, but may be configured using power from
a 9V battery (included).
Once connected to a PoE source, the Pathport Touring Edition is
ready for use.
It may be configured using its front panel or with Pathscape over
the network.
The Pathport QUATTRO operates on Power-over-Ethernet or an
auxiliary 24 or 48 VDC supply with a 2.5mm center-positive barrel
connector (supply not included).
Once powered up, the Pathport QUATTRO is ready for use. There
is no on/off switch.
The Pathport QUATTRO is designed for installation in a standard EIA
19” rack, with the LCD and encoder facing out. Attach the rack ears
(included) to either side of the enclosure using the Phillips screws
provided (two per ear). Attach the Pathport QUATTRO to the rack
using standard rack screws (not included).
A joiner is included to allow two QUATTROs to be installed side-by-
side in 1RU of rack space. Wall (P/N #9005) and truss mount (P/N
#9004) adapters are available as accessories.
PATHPORT eDIN (1011, 1012, 6824)
PATHPORT PORTABLE UNO (6151, 6152)
PATHPORT TOURING EDITION (6182)
PATHPORT QUATTRO (6321, 6322, 6326)
