background image

4

Setup:

The XA25 measures 17”w x 17.4”d x 6”h and weighs 45 pounds. You may place it 
wherever you please, but not directly on carpet - it is going to need lots of free air for 
adequate cooling.  There needs to be space above and unobstructed space around 
the sides to allow for proper air fl ow.  This is a factor in reliable operation and long life.

The XA25 is expected to have a 25-degree C rise at the sinks when running.  Under 
normal operation you should be able to grasp the heat-sinks for 5 to 10 seconds 
without heat being an issue.  If the amplifi er becomes too hot to touch please 
contact your dealer or the factory for assistance.

AC power is provided by a conventional detachable IEC 320 grounded AC mains 
power cord.  This power cord serves as the safety disconnect.  The power cord should 
be removed from the wall in the event of electrical storms or when the XA25 is not 
going to be used for long periods.  

The amplifi er is designed to perform well with the included power cord.  Should you 
select an “after market” detachable power cord, please confi ne your selection to 
those rated by local authorities to carry a minimum of 13A at 250V.

At idle the XA25 will consume 240W from the AC mains. The required voltage and 
correct fuse value will be indicated on the rear of the amplifi er.  Both 100 Vac and 120 
Vac builds are fused at 5A.  The 220 - 240 Vac build amplifi ers are fused at 2.5 amp.

Input Connection:

The XA25 accepts a single ended (RCA / Cinch) input connector.  The input 
impedance is 47 Kohm making the XA25 compatible with either tube or solid state line 
stage pre-amplifi ers or source components with a built-in volume control.

Output Connection and Loudspeakers:

The rear of the XA25 is equipped with a pair of  Furutech binding posts for each 
channel, four total.  The binding posts are marked red and black. The Red output 
connector connects to the Red (+) of your speakers and the Black connector will 
connect to the Black (-). The Black output connector is at circuit ground.  You can use 
it to connect to powered sub-woofers if you like.

Содержание XA25









Отзывы: