![background image](http://html1.mh-extra.com/html/paslode/ll350s/ll350s_operating-manual-and-parts-list_4000114006.webp)
MAINTENANCE
Paslode® tools are built for ease of maintenance. A
few simple details will assure trouble-free operation
❑
Ensure that all hardware is tight.
p
p
and long tool life. Anyone who uses or maintains the
tool must read the safety and maintenance
instructions. Study the schematic drawing before
starting any repairs on the tool.
Air-operated tools must be inspected periodically,
and worn or broken parts must be replaced to keep
th t
l
ti
f l
d ffi i
tl
Al
th
❑
Ensure that the work contacting element is
installed correctly in relation to the trigger, and that
both parts move freely.
❑
Ensure that the magazine is properly attached.
❑
Ensure that the required safety information on the
tool is legible
the tool operating safely and efficiently. Also the
items on the maintenance chart must be checked
often.
Cold Weather Care
When temperatures are below freezing, tools should
be kept warm by any convenient safe method If
tool is legible.
❑
Use only Paslode approved fasteners in the tool,
and ensure that they are correct for the application.
❑
Ensure that a male air fitting is securely
connected to the tool.
be kept warm by any convenient, safe method. If
this is not possible, the following procedure should
be used to warm up the tools.
❑
Tool operators working outdoors or in unheated
areas in extremely cold temperatures should also:
Use Paslode pneumatic oil with antifreeze in the
lubricator, Part No. 219090 (8oz.)
❑
Test the tool by driving fasteners into a work
piece identical to the tool's application.
❑
Check the tool for air leaks during testing and for
the proper sequence of operation.
❑
Ensure that all fasteners are driven to the same
depth and that the crown of the fastener is flush with
Once a week, depending on the amount of tool use,
take the tool apart and wash away any sludge with
degreaser cleaner (Paslode Part No. 219086) to
keep the tool operating efficiently.
CAUTION
depth and that the crown of the fastener is flush with
the work piece.
Tool Lubrication
It is most important that the tool be properly
lubricated by keeping the air line lubricator filled and
correctly adjusted. Without proper lubrication the
tool will not work properly and parts will wear
Cleaning the air-operated tools with solvents
removes the thin coating of grease applied to the
cylinder wall and O-rings at the factory. To replace
Never use kerosene or flammable solvents
to clean the tool.
p p
y
p
prematurely.
Use the proper lubricant in the air line lubricator.
The lubricator should be of low air flow or changing
air flow type, and should be kept filled to the correct
level. Use only Paslode recommended lubricants.
Substitutes may harm the rubber compounds in the
tools O rings and other rubber parts Paslode Part
this coating of grease, use Chemplex grease
(Paslode Part No. 403734).
❑
Open the drain on the air compressor tank to
drain any moisture at least daily in extremely cold or
humid weather. A few ounces of anti-freeze in the
tank will keep the air free of frost.
tools O-rings and other rubber parts. Paslode Part
No. 403720 is a pneumatic lubricating oil specially
made for pneumatic applications.
If a filter/regulator/lubricator is not installed on the
air system, air operated tools should be lubricated
at least once a day with 6 to 20 drops of oil,
depending on the work environment, directly
Testing the Tool After Servicing
After replacing any part or parts, it is important to
check the tool for proper operation. This ensures
that the tool was put together correctly, is safe to
use, and will perform the job properly.
p
g
y
through the male fitting in the tool housing.
Most minor problems can be resolved quickly and
easily using the maintenance table that follows. If
problems persist, contact your Paslode dealer for
assistance.
6