POWER
IR
ASC SYSTEM
SET
ASC
R F L E V E L
A F L E V E L
F E R QU Z
I N F R A R E D
- 30 - 24 - 18 - 12 - 6
- 3
0 3 dB V
5
10
1 5
20
2 5
3 0
3 5
4 0
L OW B AT T
A
B
ANTEN NA
2
5
Channel A antenna LED lamp
When it is steadily lit, Channel A antenna is
working
Channel B antenna LED lamp
When it is steadily lit, Channel B antenna is
working
LCD panel
Please See
system setting
on page 5.
System setting button
Please See
system setting
on page 5.
DOWN button of the System Menu
Please See
system setting
on page 5.
“
”
“
”
“
”
AC power adapter socket
Fine adjustment of mute threshold level
It is the mute enabling threshold value, which is factory setting and usually does
not need to be adjusted. If there are any interference signals, this threshold value
can be increased by turning the knob clockwise until RF signal lamp goes out.
1/4in output socket
Fun ctio ns of P AW-8 50 R ecei ver:
F ro nt Pa ne l
R ea r P an el
1
1
1
1
2
2
2
2
3
3
3
3
4
4
4
5
5
5
6
6
6
4
7
7
5
8
8
6
9
9
UP button of the System Menu
Please See
system setting
on page 5.
“
”
IR window
This window sends infrared signal to the transmitter
for frequency synchronization.
Synchronizing signal transmit button
Press this button to establish infrared connection
between the receiver and transmitter.
Power switch
Hold down this switch for 2 sec and then release it,
and the receiver can be turned on. If it is held down
for a longer time, the receiver will be turned off.
XLR output socket
Antenna Jack B
50 ohm.
Antenna Jack A
50 ohm
Frequency Group No. and channel selection:
Press
“
SET
key, and
“
GROUP
will flash. Press
or
key to select
”
”
suitable frequency group number, as shown in Diagram
on the left. Then
press
“
SET
key, and
“
CHANNEL
flashes. Press
or
key to
”
”
select suitable channel, as shown in Diagram
on the left.
Note:
when you use several systems, you had better set all the systems
to the same group number, and then set a special channel for each system
in this group.
Receiver Volume Control:
This device has electronic voice volume control system. Under normal
indications, press
or
key to control the output volume of the receiver
(there are 64 volume levels) as shown in Diagram
on the left.
Normal Indications on the Display:
RF level, audio level, group number, channel, and working frequency, as
shown in Diagram
on the left.
Setting of Automatic Transmitter :
Turn off the power switch of the handheld transmitter, and then open the
battery cylinder. Point its IR window to the IR window of the receiver. Press
“
ASC
key of the receiver and then turn on the power switch of the
”
handheld transmitter.
Point the IR window of the bodypack transmitter to the IR window of the
receiver. Press
“
ASC
key of the receiver and then the
“
ASC
key of
”
”
the bodypack transmitter.
Whenever the
“
ASC
key of the receiver is pressed, synchronizing signal
”
will be transmitted continuously for 25 sec, and
“
INFRARED
symbol on
”
the screen also flashes, as shown in Diagram
on the left.
When the infrared receiving circuit is enabled,
“
INFRARED
symbol on
”
the handheld transmitter will flash and the entire display screen of the
bodypack transmitter will flash (the infrared transmission indicator lamp will
also flash at the same time).
Notes:
when establishing infrared connection between the receiver and the
transmitter, the distance between them should not exceed 0.5m. When more
than one system are used, only IR window of one transmitter should be pointed
to the receiver for each infrared connection.
Battery voltage indication:
There are five-level battery voltage indications for the handheld transmitter,
and there are six-level battery voltage indications for waist worn transmitter,
as shown in Diagram
on the left.
Group Number and Channel Indication:
After infrared connection between the receiver and the transmitter is
completed, the same group number and channel as those of the receiver
will be indicated on the hand-held transmitter, and the display screen of
the waist worn transmitter will give a 5-sec steady indication of the group
and channel numbers, as shown in Diagram
on the left. Then it returns
to normal status indications.
Normal Indications on the Display:
Battery voltage, group number and channel are displayed on the handheld
transmitter, and battery voltage and working frequency are displayed on
bodypack transmitter, as shown in Diagram
on the left.
Receiving Setting:
Sys tem Set up
Ha nd h el d
t ra ns mi tt er
R
R
R
R
R
F
F
F
F
F
L
L
L
L
L
E
E
E
E
E
V
V
V
V
V
E
E
E
E
E
L
L
L
L
L
A F L E V E L
A F L E V E L
A F L E V E L
A F L E V E L
A F L E V E L
F E R Q U Z
F E R Q U Z
F E R Q U Z
F E R Q U Z
F E R Q U Z
I N F R A R E D
I N F R A R E D
I N F R A R E D
I N F R A R E D
I N F R A R E D
- 3 0
- 3 0
- 3 0
- 3 0
- 3 0
-2 4
-2 4
-2 4
-2 4
-2 4
- 1 8
- 1 8
- 1 8
- 1 8
- 1 8
- 1 2
- 1 2
- 1 2
- 1 2
- 1 2
- 6
- 6
- 6
- 6
- 6
-3
-3
-3
-3
-3
0
0
0
0
0
3d B V
3d B V
3d B V
3d B V
3d B V
5
5
5
5
5
1 0
1 0
1 0
1 0
1 0
15
15
15
15
15
2 0
2 0
2 0
2 0
2 0
2 5
2 5
2 5
2 5
2 5
3 0
3 0
3 0
3 0
3 0
3 5
3 5
3 5
3 5
3 5
4 0
4 0
4 0
4 0
4 0
L O W B AT T
L O W B AT T
L O W B AT T
L O W B AT T
L O W B AT T
1
1
1
2
3
1
2
2
2
3
3
3
4
4
5
5
BAT T
BAT T
BAT T
INFRARED
BA TT
INFRARED
BA TT
INFRARED
BA TT
Transmitter Status Indications:
Bodypack
transmitter
文件以
"pdfFactory Pro"
试用版创建
www.pdffactory.com
