Partner GBV 345 Скачать руководство пользователя страница 8

-- 8 --

WARNING:

When starting engine,

hold the unit as illustrated. Do not set unit on

any surface except a clean, hard area when

starting engine or while engine is running. De-

bris such as gravel, sand, dust, grass, etc.

could be picked up by the air intake and

thrown out through the discharge opening,

damaging the unit or property, or causing seri-

ous injury to bystanders or the operator.

STARTING A COLD ENGINE (or a

warm engine after running out of fuel)

1. Move the throttle position lever to the idle

position.

Throttle

Position

Lever

2. Slowly press the primer bulb 6 times.

3. Move the start lever to the START position.

Start

Lever

Starter

Handle

Primer

Bulb

4. Pull starter rope handle sharply 5 times (no

more than 3 times above 32

˚

C/90

˚

F). If en-

gine starts and runs prior to 5 pulls, allow en-

gine to run for 5 seconds; then, fully squeeze

the throttle trigger to disengage the starting

system (start lever returns to RUN position).

Steps 5 and 6 are not necessary.

5. Fully squeeze the throttle trigger to disen-

gage the starting system (start lever returns

to RUN position).

6. Pull starter rope handle sharply while

squeezing throttle trigger until engine starts

and runs.

STARTING A WARM ENGINE

1. Squeeze and hold the throttle trigger.

2. Pull starter rope handle sharply while

squeezing throttle trigger until engine starts

and runs.

NOTE:

Normally, the warm starting proce-

dure can be used within 5--10 minutes after

the unit is turned off. If the unit sits for more

than 10 minutes without being used, it will be

necessary to start the unit by following the

steps under STARTING A COLD ENGINE or

following the starting instruction steps shown

on the unit.

STARTING A FLOODED ENGINE

Flooded engines can be started by moving the

start lever to the RUN position and fully

squeezing the throttle trigger. Pull the starter

handle repeatedly while squeezing throttle

trigger until engine starts and runs. This could

require pulling the starter handle many times,

depending on how badly the unit is flooded. If

the unit still doesn’t start, refer to the TROU-

BLESHOOTING TABLE.

Содержание GBV 345













Отзывы: