background image

 

All-in-one solar charge inverter    V11                                                                                                                                                               32 

5. Other functions 

5.1 Dry node 

Working principle: This dry node can control the ON/OFF of the diesel generator to 

charge the battery.  ① Normally, the terminals are that the NC-N point is closed and 

the NO-N point is open; ② When the battery voltage reaches the low voltage 

disconnection point, the relay coil is energized, and the terminals turn to that the  

NO-N point is closed while NC-N point is open. At this point, NO-N point can drive 

resistive loads: 125VAC/1A, 230VAC/1A, 30VDC/1A. 

 

5.2 RS485 communication port

 

This port is an RS485 communication port ;  

This port is an RS485-2 communication port is an optional function, which is not available in the 

standard machine. 

This port is an RS485-1 communication port which comes with two functions: 

①  It allows direct communication with the optional host computer developed by our 
company through this port, and enables monitoring of the equipment running status 
and setting of some parameters  on the computer;  
②   It  also  allows  direct  connection  with  the  optional  RS485  to  WiFi/GPRS  
communication  module  developed  by  our  company  through  this  port.  After  the 
module is selected, you can connect the all-in-one solar charge inverter through the 
mobile phone WiFi/GPRS APP, on which you can view the operating parameters and 
status of the device. 
  

As shown in the figure:

  

Pin 1 is 5V power supply, Pin 2 is GND, Pin 7 is RS485-A, and Pin 8 is RS485-B ; 

 
5.3 USB communication port 

This is a USB communication port, which can be used for USB communication with 

the optional PC host software. To use this port, you should install the corresponding 

"USB to serial chip CH340T driver" in the computer. 

 

 

Содержание HF4830S60-145








































Отзывы: