Parsun F6ABM Скачать руководство пользователя страница 61

Страница: 61 / 63

Continuation /…2

Trouble type

Possible reason

Recovery action

Engine power

loss

Propeller is damaged

Repair or replace propeller

Trim angle is incorrect

Adjust trim angle to achieve most
efficient operation

Motor is mounted at incorrect transom
height

Adjust motor to proper transom
height

Boat bottom is fouled with marine growth

Clean boat bottom

Weeds or other foreign matter are tangled
on gear housing

Remove foreign matter and clean
lower unit

Spark plug(s) are fouled or incorrect
type

Inspect spark plug(s). Clean or
replace with recommended type

Fuel system is obstructed

Check for pinched or kinked fuel line
or other obstructions in fuel system

Fuel filter is clogged

Replace with recommended type

Fuel is contaminated or stale

Fill tank with clean, fresh fuel

Spark plug gap is incorrect

Inspect and adjust as specified

Ignition wiring is damaged or poorly
connected

Check wires for wear or breaks.
Tighten all loose connections.
Replace worn or broken wires

Ignition parts have failed

Have serviced by your dealer

Specified engine oil is not being used

Check and replace oil as specified

Содержание F6ABM
































































Результаты поиска

Содержание F6ABM

Отзывы:

Похожие инструкции для F6ABM

Бренды по названию

Популярные бренды

Parsun F6ABM, Руководство пользователя

Результаты поиска

Содержание F6ABM

Отзывы:

Похожие инструкции для F6ABM

Бренды по названию

Популярные бренды