Parrot Uncle F8216110V Скачать руководство пользователя страница 7

C

R

2 0 3 2

3 V

LEARN

O

0

D

1

Forward or reverse operation: change fan rotating direction.

Natural Wind: Press the button to change fan rotating direction. Fan speed
changes within its range creating gentle natural wind effect.

Lamp on-off control

When the first one dial down to the position of “D” and the light is on, long press 
the button adjustable light, dimmer in the process, when the light bulbs reach to 
most bright and dark, have a “Beep” sound tip respectively.

(*This f

unction

requires adjustable brightness product support).

FAN SPEED

Fan speed 1 – 6 control (1-low speed, 6-high speed)

Turns off the fan

Timing the fan

Auto off after 1 hr

Auto off

 

after 3 hr

Auto off after 6

 

hr

Cancel timing setup

1hr

6hr

3hr

6

3

5

4

1

2

6

3

5

4

1

2

1hr

6hr

3hr

TRANSMITTER SETTING

To use factory pre-programmed setting - Skip the below programming steps. 
Insert battery into transmitter, turn on the power supply to fan and it is ready 
to use.

Read all the steps BEFORE proceeding. Each step must be followed exactly 
in order to program the transmitter. 

FIRST ONE USE INSTRUCTION
1) Dial up to position“O”, it is on/off only for the lighting, and it is the brightest 
of the light.
2) Dial down to position“D”, the brightness of the light can be control low or 
high.(*This f

unction

 requires adjustable brightness product support).

SECOND ONE USE INSTRUCTION
1) If you have more than 1 unit of this fan model in close proximity, it is 
equipped self-learning, please don’t press any key when self-learning.
2) To set the second one down to the position of “1” (set to “0” position on 
one product when used directly).
3) Turn on the power of the light fan.
4) Within 30 sec after the “Beep”, press and hold the LEARN button for 3 
sec. Once the receiver has detected and learned the frequency, the receiver 
will “Beep” twice, meanwhile the light will bright out twice. Programming/self-
learning process is completed and fan is ready to use.

TRANSMITTER FUNCTION

F821

6

110V 

Installation & Operating Instructions for the 

Parrotuncle Owner's Installation, Manual 

WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER 

Содержание F8216110V













Отзывы: