Parrot Uncle F6261110V Скачать руководство пользователя страница 2

UNPACKING YOUR CEILING FAN

Open the original carton and verify the following items are available for the standard purchase of this product. It there are any missing or mechanically damaged items, contact the Mercator 

Customer Care. Do not throw away the carton or other packaging material as it may be needed if warranty replacement or repair is ever necessary

.

  

Balance Kit

Wood Screw (

x4

)

Metal Washer (

x4

)

Spring Washer (

x4

)

Wiring cap

(

x6

)

Joint screw

 (

x1

)

S

crews 

(

x2

)

S

tar washers(

x

4)

Fan blades (

x3

)   

Fan hanger

derrick

Joint cover

Decorative covers

Remote control

Receiver

Canopy

Fan motor assembly

led light kit

Lamp panel 

Chimney

Leaf blade arm

(

x3

)

CAUTION

· 

Use of an unapproved remote controller voids the warranty

.

 

Therefore do not control the operation of this fan from any remote controller that is not approved by Mercator for use with this fan.

· 

Do not use solid state controllers.

3

2

1

2 4 8

hr

FAN INSTALLATION INSTRUCTIONS

Make sure electricity is turned off at the main power box before commencing work. Turn off the power by removing fuse or turning off circuit breaker before installing the fan and replacing the lamps.

• 

The lowest point on the fan blade must be at least 2.1 metres (7 feet) from the floor

.

• 

Make sure that ceiling joists are strong enough and of adequate size to support the weight of the fan of about 35 kg.

WARNING

Step 1

  

Install Mounting

 

Bracket

Install  the  mounting  bracket  onto  the  electrical 
junction  box  in  the  ceiling  using  two  machine 
screws,  two  washers  and  two  lock  washers 

(

see 

figure 1)

.

The mounting bracket has slotted holes to enable
it to move sideways for proper alignment. Make
sure  the  mounting  bracket

 

is  centered  over  the 

electrical  junction  box  and  that  it  is  securely 
attached 

(

see figure 2)

.

NO MOVEMENT SHOULD OCCUR

BETWEEN

THE

MOUNTING

BRACKET AND THE ELEC-

TRICAL

JUNCTION

BOX.

Fig. 1

Junction 

Box

F6261110V 

Installation & Operating Instructions for the

 

Parrotuncle Owner’s Installation ,Manual

WARNING

SHU

T

 

P

OWER OFF AT FUSE OR CIRCUIT BREAKER

Parrotuncle Lighting, 218 Black Tie Lane, Chapel Hill, NC www.parrotuncle.com

 

Parrot Uncle   YOU CAN BE SURE OF are trademarks of Eileen Grays

 

LLC.

 

Used under license by  Eileen Grays LLC.

Made in CHINA

All rights reserved.

Содержание F6261110V









Отзывы: