F6236
Installation & Operating Instructions for the
Owner’s Installation ,Manual
WARNING:SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
WARNING: To avoid possible electrical shock, be sure
electricity is turned off at the main fuse box before wiring.
1. Insert the receiver into the mounting bracket with the flat
side of the receiver facing the ceiling.Motor to Receiver
Electrical Connections: Connect the Black wire from the fan
to Black wire from the receiver. Connect the white wire from
the fan to the white wire from the receiver.Connect the Blue
wire from the fan to the Blue wire from the receiver.Secure
wire connections with the wire nuts provided.
2. Receiver to House suppliy wires Electrical Connections:
Connect the Brown(hot) wire from the ceiling to the Brown
wire from the receiver. Connect the Blue(neutral) wire from
the ceiling to the Blue wire from the Receiver. Secure the
wire connections with the wire nuts provided.
3. Light kit to motor wires Electrical Connections: Connect
the two wires from LED module to the black and blue wires
from fan
AFTER INSTALLATION
WOBBLE”
The fan blades have been adjusted in the factory to minimize any wobble
NOTE:CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT
THEY ARE MOUNTED ON A RUBBER CROMMET. IF THE FAN WAS MOUNTED
RIGIDLY TO THE CEILING, IT WOULD CAUSE EXCESS VIBRATION. MOVEMENT OF A
FEW CENTIMENTERS IS QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY
PROBLEM
TO REDUCE THE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH
SECURED THE MOUNTING BRACKET AND DOWNROD ARE SECURE.
BALANCING A WOBBLING CEILING FAN:
For your convenience, a Balancing Kit is included; please follow this procedure when
balancing the fan:
1. Check that all blade and blade arm screws are secure.
2. Most fan wobbling problems are caused when blade levels are unequal. Check this
level by selecting a point on the ceiling above the tip of one of the blades. Measure this
distance.Rotate the fan until the next blade is positioned for measurement. Repeat for
each blade. The distance deviation should be equal within 1/8"(0.32cm).
3. Use the enclosed Blade Balancing Kit if the blade wobble is still noticeable.
4. If the blade wobble is still noticeable, interchanging two adjacent (side by side)
blades can redistribute the weight and possibly result in smoother operation.
WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE ARM WHILE INSTALLING, BALANCING THE BLADES, OR CLEANING THE
FAN. DO NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.
NOISE
When it is quiet(especially at night) you may hear occasional small noises. This is
normal. Please allow a 24-hour “breaking-in” period, most noises associated with a
new fan disappear during the time.
CARE AND CLEANING
1. Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft
brush or lint free cloth to avoid scratching the paint finish. Please make sure to turn off
electricity power before you clean your fan
2. Do not use water when cleaning your ceiling fan. It could damage the motor or the
blades and create the possibility of an electrical shock.
3. Motor has permanently lubricated ball bearing. No need to oil
NOTE: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE
YOU ATTEMPT ANY CLEANING OR REPAIRS.
F6223
Installation & Operating Instructions for the
Owner’s Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
BEFORE INSTALLATION
Unpack your fan and check the contents.You should have followings:
1. Mounting bracket
2. Mounting screws
3. Canopy
4. Downrod & hanger ball
5. Canopy cover
6. Coupling cover
9. Top housing
10. Lower housing
11. Fan motor assembly
12. Screws for blades
13. Blades
14. Blade bracket
18. Wood screws
19. Expansion screws
20. Screw washers
21. Balancing tape
22. Balancing clip
23. Remote control set.
7. Bolt
15. Screws for blade bracket
18 19 20 21
22
2 4 8
hr
1
2
3
23
16
13
1
2
3
4
5
17
6
7
8
9
10
11
14
12
15
8. Lock pin
16. Screws for light kit
17. Light kit
