Parrot Uncle BBCF235 Скачать руководство пользователя страница 25

8. Reverse Switch Operation 

(Continued)

8.3

Replace  the  Shade  into  the  opening  in  the  Lower 

Housing, aligning the Three Flat Areas on the top edge 

of  the  Shade  with  the  Lower  Housing  Three  Raised 

Dimples  and  turn  the  Shade  Clockwise  until  it  stops 

(Figure 41).

NOTE: Periodically check that the Shade is seated 

fully clockwise in the Lower Housing.

CLOCKWISE

LOWER HOUSING 

RAISED DIMPLES (3)

FLAT AREAS (3)

SHADE

Figure 41

25

LED LIGHT FIXTURE 

ASSEMBLY

REVERSE SWITCH

   Figure 40

8.2

Slide  the  Reverse  Switch  (located  on  the  side  of  the 

LED  Light  Fixture  Assembly)  to  the  opposite  position, 

and turn the Ceiling Fan ON again (Figure 40).
The Fan Blades will turn in the opposite direction and 

reverse the airflow.
During  Summer  Months,  run  the  Fan  Counter-

Clockwise,  as  you  look  up  at  it,  to  direct  airflow 

downward.
During  the  Winter  Months,  run  the  Fan  Clockwise,  as 

you look up at it, to direct airflow upward.
If  airflow  is  desired  in  the  opposite  direction,  turn  the 

Ceiling Fan OFF and wait for the Blades to stop turning.

Reverse Switch Information

Season 

Blade Rotation Direction 

Summer 

Counter-Clockwise 

Winter 

Clockwise 

BP7544-1 CF235 Astor (EnSpFr) 201208.indb   25

12/8/20   9:24 PM

Содержание BBCF235





























Отзывы: