Installation & Operating Instructions for the
Parrotuncle Owner's Installation ,Manual
WARNING: SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
530173SQ-SMART
2. OPERATING TRANSMITTER:
Operating the buttons on the panel of the transmitter.
3 key -for fan high speed.
2 key-for fan medium speed.
1 key-for fan low speed.
OFF key-for fan off.
REV key-for fan rev.
LIGHT key-for light on and off.
LIGHT+ key-for light .
LIGHT- key-for light dimmer -.
YOUR REMOTE NOW HAS FULL CONTROL OF THE FAN AND LIGHT.
3. TROUBLE SHOOTING GUIDE
a. Power to receiver ?
b. Receiver wired correctly ?
c. Fan manual speed control in highest position ?
d. Light kit switch turned on ?
e. Good battery in the transmitter ?
OPERATION DISTANCE 20 FEET
MODEL:
RE-021
If there are two or more ceiling fans installed in the same house, in order to prevent your ceiling fans from being affected
by the remote control of the adjacent ceiling fans, first turn the switch in each remote control transmitter to the CODE
(
locked
)
position
(
see
the
schematic
diagram
FIG
1
) Remarks: The standard s tate of t he transmitter i s i n t he common
code COM.
(
Power
-
off
means
you
need
to
use
a
wall
switch
to
shut
down
the
power
of
the
ceiling
fan
,
if
you
do
not
have
a
wall
switch
,
please
power
off
the
whole
room
from
the
air c ircuit-breaker f or each r oom)
After installing the remote control receiver on the ceiling fan
1: Turn on the power of the 1# ceiling fan receiver (the power of the 2# receiver is kept in a power-off state), within 30 seconds
after the fan power is turned on, press the LEARN button corresponding to the 1# transmitter, then The receiver will learn the
transmitter code. When the transmitter code is learned successfully, the light of the
ceiling fans will flash twice, and then it can be
used normally.
2: Turn on the power of the 2# ceiling fan receiver (the power of the 1# receiver is kept in the power-off state), within 30 seconds
after the fan power is turned on, press the LEARN button corresponding to the 2# transmitter, then The receiver will learn the
transmitter code. When the transmitter code is learned successfully, the light of the ceiling fans will flash twice, and then it can be
used normally.
And so on, only one ceiling fan is powered on each time the corresponding transmitter learns.
FCC Statement:
1.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)
This device may not cause harmful interference.
(2)
This device must accept any interference received, including interference that may cause undesired operation.
2.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to Part 15 or the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may casue harmful interference to radio communications,
However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
--- Reorient or relocate the receiving antenna.
--- Increase the separation between the equipment and receiver.
--- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
--- Consult the dealer or an experienced radio/ TV technician for help.
WARNING
TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH A WALL CONTROL/SWITCH.
TRANSMITTER
LEARN
CODE
COM
CODE
ACN
ACL
ANT
COM
FAN
LIGHT
INPUT
OUTPUT
RECEIVER
FIG1
REV
