Parkside PTBMOD 710 B2, Руководство по эксплуатации и технике безопасности

Страница: 10 / 64

5 GB
d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools and accessories.
Check for misalignment or binding of moving parts, break-
age of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poor-
ly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery han-
dles and grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts.
This will ensure that the safety of the power tool
is maintained.
Drill safety warnings
a) The drill must be secured. An incorrectly secured drill
can move or topple and this can result in injuries.
b) The workpiece must be clamped or fastened
to the workpiece support. Do not drill into
workpieces that are too small to be securely
clamped.
Holding the workpiece by hand can lead to
injuries.
c) Do not wear gloves. Gloves can be caught by rotating
parts or drilling debris and thus cause injuries.
d) Keep your hands away from the drilling area
whilst the electrical tool is running. Contact with
rotating parts or drilling debris can cause injuries.
e) The drill must be turning before it makes con-
tact with the workpiece. Otherwise, the drill bit can
catch in the workpiece and this can result in an unexpected
movement of the workpiece and cause injuries.
f) If the drill becomes jammed, stop pressing
downwards and switch the electrical tool off.
Investigate and rectify the cause of the jam-
ming.
Jamming can result in an unexpected movement of
the workpiece and can result in serious injuries.
g) Avoid long pieces of drill swarf by interrupting
the downward pressure at regular intervals.
Sharp metal swarf can become tangled and lead to in-
juries.
h) Never remove drilling debris from the drilling
area whilst the electrical tool is running. To
remove swarf, move the drill away from the
workpiece, switch off the electrical tool and
wait until the drill has come to a standstill. Use
an aid such as a brush or a hook to remove the
swarf.
Contact with rotating parts or drilling debris can
cause injuries.
i) The permissible rotational speed for drill bits
with a rated speed must be at least as high as
the highest speed cited on the electrical tool.
Ac-
cessories that rotate faster than permitted can break and
fly off at high speed.
Attention: Laser radiation
Do not look into the beam
Laser class 2
Protect yourself and you environment from acci-
dents using suitable precautionary measures
• Do not look directly into the laser beam with unprotected
eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting surfaces and
persons or animals. Even a laser beam with a low output can
cause damage to the eyes.
• Caution - methods other than those specified here can result
in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure to the
beam can occur.
• The laser may not be replaced with a different type of laser.
• Repairs of the laser may only be carried out by the laser
manufacturer or an authorised representative.
• Labelling and placement of warning stickers, see fig. 8 and
9.
m WARNING! This electric tool generates an electromag-
netic field during operation. This field can impair active or
passive medical implants under certain conditions. In order to
prevent the risk of serious or deadly injuries, we recommend
that persons with medical implants consult with their physician
and the manufacturer of the medical implant prior to operating
the electric tool.
Residual risks
Even when this electric tool is operated properly,
residual risks still remain. The following hazards
may arise in connection with the design and con-
struction of this electric tool:
• Lung damage if suitable dust protection mask is not worn.
• Hearing damage if suitable hearing protection is not worn.
• Damage to health resulting from hand/arm vibration if the
device is used over an extended period of time or if it is not
properly operated and maintained.