15
GB/IE/CY
Operation
j
Tighten the stop screw
9
for depth stop
10
again.
j
Release the clamping lever
15
by turning it
clockwise and then guide the device back up
again. Check the depth of cut by carrying out
a further practical test.
Setting the depth of cut using the step
buffer
You can use the step buffer
7
to make greater
depths of cut in several successive stages in which
less material is removed.
j
Set the required depth of cut with the lowest
step of the step buffer
7
(as described
above).
j
Afterwards the higher steps can be used for
the first few cuts.
Q
Direction of feed
m
Danger!
When machining with the direction
of rotation the router can be ripped out of your
hands. This may cause injury.
J
Always machine against the direction of
rotation of the router bit!
Q
Routing process
j
Adjust the depth of cut as described above.
j
Place the device on the workpiece and switch
it on.
j
Release the clamping lever
15
by turning it
clockwise and press the device downwards un-
til the depth stop
10
runs against the workpiece.
j
Lock the device by turning the clamping lever
15
anticlockwise.
j
Carry out the routing process using uniform
speed and pressure
j
Stop the routing process by lifting the device
from the workpiece and switching it off.
Q
Setting the guide bushing
j
Insert the guide bushing
35
from below into the
guide plate
6
.
j
Fasten the guide bushing
35
to the base plate
5
using the two screws
30
of the vacuum ex-
traction adapter. Make sure that the guide
bushing
35
is the right way round - the guide
bushing ring
36
must be facing downwards.
Q
Routing with the guide bushing
Note!
When using the guide bushing, the template
must have a minimum thickness of 8 mm.
Note!
The template must be at least as thick as
the guide bushing ring
36
of guide bushing
35
.
Note!
Choose a router bit with a smaller diameter
than the internal diameter of the guide bushing.
By using the guide bushing
35
you can superimpose
templates or patterns on to the workpiece.
j
Place the device with the guide bushing
against the template.
j
Release the clamping lever
15
by turning it
clockwise and lower the device until the previ-
ously set depth of cut is reached.
j
Now guide the device with the projecting
guide bushing along the template, whilst apply-
ing light pressure.
Q
Routing with the guide fence
j
Insert the guide fence
27
into the guide rails
22
of the base plate
5
and fasten it into place to
suit the required dimension using the locking
screw
21
.
Содержание POF 1300
