Parkside MPKZ 2000 A1, Руководство по эксплуатации и технике безопасности

Страница: 13 / 95

8 GB
8. Before starting the equipment
• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport damage.
• If possible, store the packaging until the warranty period
has expired.
m DANGER
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
8.1 Mounting the transport handle (fig. 3.1)
ATTENTION!
The correct position of the transport handle (39)
is specified by a groove.
• Mount the transport handle (39) on the machine head (4)
using the Phillips screws 5.0 x 25 mm.
• Then tighten the two Phillips screws 5.0 x 25 mm (40) with a
Phillips screwdriver (not included in the scope of delivery).
8.2 Setting up the machine (fig. 3.2)
• The machine must be set up where it can stand securely.
• Secure the machine on a workbench, base frame or similar.
• Insert 4 screws (not included in the scope of delivery) into
the holes on the fixed saw table (15).
• Tighten up the screws.
8.3 Installing the tilt protection (fig. 3.2)
• Loosen the tilt protection (36) pre-installed at the bottom of
the saw.
• Pull the tilt protection (36) out, so that it can still be fixed
with the aid of the Allen screws.
• Secure the tilt protection again with an Allen key (D).
8.4 Setting the adjustment screw (fig. 3.3)
• Set the adjustment screw (37) to the level of the tabletop to
avoid wobbling of the machine.
8.5 General information
• All covers and safety devices have to be properly fitted be-
fore the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed before,
watch out for foreign bodies such as nails or screws, etc.
• Before you press the ON/OFF switch check that the saw
blade is fitted correctly. Moving parts must run smoothly.
• Before you connect the equipment to the power supply make
sure the data on the rating plate are identical to the mains
data.
8.6 Checking the moving saw blade guard safety
device (5)
The saw blade guard protects against accidental contact with
the saw blade and from chips flying around.
8.6.1 Check function
To do so, fold the saw downwards:
• The saw blade guard must provide free access to the saw
blade without touching other parts.
• When folding the saw upwards into the starting position, the
saw blade guard must cover the saw blade automatically.
9. Attachment
You need:
1x Allen key 6 mm (C)
1x Allen key 3 mm (D)
(included in the scope of delivery)
1x open-ended spanner 13 mm
1x Phillips screwdriver
(not included in the scope of delivery)
9.1 Attaching the multifunction sliding cross cut mi-
tre saw (fig. 1/2/3.3/4)
• In order to adjust the rotary table (14), fold the locking han-
dle (11) upwards and pull up the latched position lever (35)
with your index finger.
• Turn the rotary table (14) and pointer (12) to the desired
angle measurement of the scale (13). To fix the setting, fold
the locking handle (11) downwards.
• Press the machine head (4) lightly downwards and remove
the locking bolt (23) from the motor bracket. Thus, the saw
disengages from the lowest position.
• Swing the machine head (4) up.
• It is possible to secure the clamping devices (7) to the left or
right on the fixed saw table (15). Insert the clamping devices
(7) into the holes provided on the back of the stop rail (16)
and secure them with the wing screws (7a).
For 0°- 45° mitre cuts, the clamping device (7) must only be
mounted on the right side (see fig. 14-15).
• It is possible to tilt the machine head (4) a max. 45° to the
left by loosening the set screw (22).
• Workpiece supports (8) must always be secured and used
during work. Define the desired table size (see 9.1.1.).
9.1.1 Defining the table size
• Loosen the set screw (9).
• Pull out the workpiece support (8) to the desired table size.
• Tighten the set screw (9) again.
9.2 Chip collection bag (fig. 1/5)
The saw is equipped with a chip collection bag (17) for saw-
dust and chips.
Attention! The chip collection bag may only be used when
cutting wood and wood-like materials! When cutting metal,
there is a risk that hot chips will ignite the chip collection bag.
Squeeze the wings of the metal ring on the chip collection bag
(17) together and slide it over the extraction port (17a) near
the engine.
The chip collection bag (17) can be emptied by means of a
zipper at the bottom.