Parkside 43.006.88, Инструкции по эксплуатации и безопасности

Страница: 15 / 24

GB
15
Idle speed
Sound pressure level L
pA
86 dB(A)
Sound power level L
WA
99 dB(A)
The values given are emission values and are
therefore do not necessarily depict the values
of a safe place to work. Although there is a
correlation (interdependence) between
emission and immission levels, it cannot be
reliably deduced whether or not additional
measures for caution are necessary. Factors
affecting the existing immission level at the
workplace include the duration of the exposure,
the characteristic of the workroom, other
sources of noise, etc., e.g. the number of
machines and other procedures in the vicinity.
The reliable values for the workplace can also
vary from country to country. This information
should however enable the operator to more
reliably estimate the dangers and risks
involved.
7. Before starting the equipment
7.1 General information
The equipment must be set up where it can
stand securely, i.e. it should be bolted to a
workbench, a universal base frame or
similar.
All the covers and safety devices have to
be properly fitted before the machine is
switched on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign
bodies such as nails or screws etc.
Before you press the ON/OFF switch check
that the saw blade is fitted correctly. Moving
parts must run smoothly.
Before you connect the equipment to the
power supply make sure the data on the
rating plate are identical to the mains data.
7.2 Assembling the saw (Fig 1-3, 5-6)
Screw together the locking grip (13) and
mounting thread (e).
To adjust the turntable (16), loosen the
locking grip (13) by approx. 2 turns, which
frees the turntable (16).
Push the latched position lever, turn the
turntable (12) and scale pointer (16) to the
desired angular setting on the dial (14) and
lock into place with the locking grip (15).
The saw has latched positions at the
following angles: - 45°, -30°, -22.5°, -15°,
0°, 15°, 22.5°, 30° and 45°, into which the
latched position lever snaps into place.
To release the saw from its bottom position,
apply light downward pressure to the
machine head (5). At the same time pull the
safety pin (25) out of the motor mount. Turn
the safety pin (25) through 90° so that the
saw remains unlocked.
Swing the machine head (5) up until the
release lever (3) latches into place.
Fit the clamping devices (8) on the left
and/or right side of the fixed saw table (17).
Undo the locking screws for the workpiece
support (10).
Mount the workpiece support (9) on the
fixed saw table (17) and tighten the
appropriate locking screw (10) (Figure 5).
Mount the second workpiece support (9) on
the opposite side of the saw and secure
with the appropriate locking screw (10).
When the locking screw (23) is loosened,
you can tilt the machine head (5) to the left
by up to 45°.
Screw the additional stability bar (18) to the
back of the equipment. (Figure 6)
7.3 Final adjustment of the stop for
crosscut 90° (Fig. 7-8)
An angular stop is not supplied.
Fasten the turntable (16) in 0° position.
Undo the securing screw (23) and tilt the
machine head (5) as far to the right as
possible using the handle (1).
Place the 90° angular stop (a) between the
saw blade (7) and the turntable (16).
Slacken the counternut (d). Adjust the
adjustment screw (29) until the angle
Anleitung_ZKGS_2100_4300688:_ 25.11.2008 8:30 Uhr Seite 15