Parker PCS-2600 Скачать руководство пользователя страница 3

4

5

GENERAL SAFETY

• 

WARNING! Read and fully understand this user manual before operating the machine.

• 

WARNING! Never allow children to use the machine. 

• 

WARNING! The chainsaw has been specially designed for tree maintenance and should only be used by trained operators. 

• 

NEVER operate the chainsaw when fatigued, ill or under the influence of medication, alcohol or drugs. 

• 

ALWAYS USE safety equipment; appropriate footwear, eye protection, ear protection, head protection, trousers and gloves. 

• 

ALWAYS keep the chainsaw sharp and well maintained.  A dull chain causes vibration which can damage the machine.

• 

ALWAYS inspect the chainsaw before use for worn, loose or damaged parts. 

• 

ALWAYS carry the chainsaw with the engine stopped, with the guide bar and chainsaw facing to the rear.

• 

DO NOT start the engine within 3m of the fuelling point.

• 

REMOVE all sources of sparks and flames before mixing and pouring fuel. 

• 

DO NOT let anyone near the chainsaw when starting or cutting.  Keep everyone, especially children, away from the work area. 

• 

KEEP all parts of your body away from the saw chain when the engine is running.

• 

DO NOT start cutting until you have a clear cutting area and a secure footing.

• 

NEVER cut trees or foliage in high wind, bad weather or when there is poor visibility.

• 

GUARD AGAINST kickback. Kickback can cause loss of control. 

• 

DO NOT operate the chainsaw with one hand. 

• 

ALWAYS Hold the chainsaw firmly with both hands.

• 

BE ALERT for the phenomena of "skating" and "bouncing".

• 

BE CAUTIOUS not to lose balance of your body due to "drop" at the end of a cut.

• 

ALWAYS keep the handles dry, clean and free of oil and fuel mixture. 

• 

ALWAYS shut off the engine before putting the chainsaw down. 

• 

ONLY OPERATE the chainsaw outdoors or in well ventilated areas.

• 

MAKE SURE the guide bar protector is in place when transporting the chainsaw.

• 

ALL MAINTENANCE other than that listed in this manual, should be carried out by professionally trained and certified personnel. 

SYMBOLS ON THE MACHINE

FUEL FILLER POINT

CHAIN OIL FILLER

CHOKE CLOSED

CHOKE OPEN

CHOKE LEVER OUT (ON) - COLD START 

CHOKE LEVER IN (OFF) - WARM START

HIGH SPEED ADJUSTMENT SCREW

LOW SPEED ADJUSTMENT SCREW

IDLE ADJUSTMENT SCREW

CHAIN BRAKE DIRECTION 

• 

WHITE ARROW - RELEASED (OFF)

• 

BLACK ARROW - ACTIVATED (ON)

CHAIN OIL ADJUSTMENT SCREW

ON/OFF SWITCH 

WITH THE "I" POSITION DEPRESSED THE ENGINE WILL START

WITH THE "O" POSITION DEPRESSED THE ENGINE WILL STOP

H

L

T

For safe operation and maintenance symbols are moulded in relief on the machine or shown on a label.

MIN           MAX

STOP

Содержание PCS-2600






























Отзывы: