Parker Compax3H C3H050V4 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 44

Parker Compax3H C3H050V4 Скачать руководство пользователя страница 23

Parker EME

Connections of Compax3H

192-120149 N08 June 2014

23

Recommended tightening torques

High voltage supply

Ballast resistor

Grounding

C3H050V4

4Nm / 35lb-in

4Nm / 35lb-in

4.5Nm / 40lb-in

C3H090V4

6-8Nm / 53-70lb-in

6-8Nm / 53-70lb-in

6-8Nm / 53-70lb-in

C3H1xxV4

15-20Nm / 132-177lb-in

0.7Nm / 6.1lb-in

42Nm / 375lb-in

Cable glands

Use metallic cable joints permitting a 360° shielding in order to comply with the EMC
directive.

2

1

1: Cable feed through plate
2: metallic joint with 360° shielding for EMC compliant design

The device must be grounded without interruption according to EN 61800-5-1. The
mains supply lines must be protected with a suitable fuse or a circuit breaker (FI
switches or earth fault fuses are not recommended).
For installation in accordance with EN 61800-5-1 mm Europe:



For grounding without interruption, two separate protective leads (

²

cross-section)

or one lead (>10mm

²

cross-section) are required. Each protective lead must meet

the requirements according to EN 60204.

This manual was downloaded on www.sdsdrives.com

+44 (0)117 938 1800 - [email protected]

«
...
21
22
23
24
25
...
»

Содержание Compax3H C3H050V4













































Отзывы:

Нет отзывов