Paras
sound
®
ZoneMa
Rear
Channel
zone but
Always d
connectio
this powe
there is no
cause the
Audi
Bus 1 a
These are
the input f
input for o
Bus 2 S
This is an
enables th
output jac
the speak
sound qua
connected
Input swit
jacks whic
Note
conn
Note
to att
shou
circu
your
perfo
Line Inp
These are
output jac
Ensure th
aster
™
1250 Own
r Panel
pairs (left an
this will be d
isconnect th
ons.
Insertin
r amp is turne
o strain or ten
em to pull loos
io Inpu
nd Bus 2 I
e standard RC
for one or mo
one or more z
Speaker Le
additional ty
he ZoneMaste
cks. This is a
ker terminals o
ality of the sp
d to the Bus 2
ch to Bus 2.
ch provide a l
e:
You should
nector, but no
e:
You can de
tach and secu
uld be twisted
uit the amplifie
receiver's po
ormance adva
put Jacks f
e standard lin
cks on your pr
at the Input s
ner’s Manual
l Audio
nd right) are
determined b
he AC cord to
g or removing
ed on can res
nsion on any
se.
ut Conn
nput Jacks
CA line level a
ore zones set
zones set eac
vel Input C
pe of audio in
er 1250 to co
high impeda
on any receiv
peakers that a
2 Speaker Lev
Speaker leve
ine level outp
d connect only
t both.
etach the spea
ure the 4 spe
tightly and/o
er. Since the
ower output us
antage.
for Channe
e level audio
reamp, whole
switch is set to
o Conn
grouped into
by the system
o your ZoneM
g an interconn
sult in a burst
input cables,
nectio
s
audio Inputs t
each zone’s
ch zone’s Inpu
Connector
nput that any
onnect to any
nce input and
ver or amplifie
are already co
vel input conn
el audio is als
put to drive ad
y the Bus 2 In
aker input con
aker wires. It
r tinned with s
Speaker Lev
sing large gau
els 1 throu
Inputs for ea
e-house audio
o Line In for e
nection
o 6 zones. T
m integrator
Master 1250 b
nect cable’s p
of sound that
speaker wire
ons
that any zone
Input switch t
ut switch to its
zone can sele
audio receive
d the ZoneMa
er. This will n
onnected direc
nector can be
o converted t
dditional amp
nput jacks or t
nnector block
t accepts bar
solder to prev
vel input consu
uge speaker w
gh 12
ch channel. C
o controller or
each zone tha
ns
Typically eac
.
before plugg
plug from any
t can damage
es DC trigger w
e can select a
to its Bus 1 po
s Bus 2 positi
ect as its sou
er or stereo sy
aster 1250’s s
ot reduce its
ctly to the “ho
e routed to an
to line level an
lifiers.
the Speaker L
k from the 125
re wires up to
vent stray stra
umes a small
wire provides
Connect thes
r the zone out
at is connecte
h room or ar
ging in or unp
y power amp’s
e your loudsp
wires or the A
as its source.
osition. To se
on.
rce. The spe
ystem even if
speaker level
output power
ost” receiver o
ny zone by se
nd routed to t
Level input
50 to make it
AWG 16. Ea
ands that cou
l fraction of a
s absolutely n
se jacks to the
tputs of your A
ed this way.
rea is consid
plugging any
s input jacks w
peakers. Mak
AC cord that c
To select Bu
elect Bus 2 as
eaker level inp
f it lacks prea
input can con
r or degrade t
or amplifier. A
tting each zo
the Bus 2 Loo
easier
ach wire
uld short
watt of
no
e Left and Rig
AV receiver.
Page 7
dered a
y
while
ke sure
could
us 1 as
s the
put
mp
nnect to
the
Audio
ne’s
op Out
ght
