background image

14

JC 2 also insure the best possible analog connection to source components which are equipped 
with balanced outputs.  
We generally recommend balanced connections if your power amplifiers or source equipment 
are located more than 10 feet from your JC 2. Many serious listeners prefer the sonic  
characteristics of balanced connections because their lower inherent noise floor contributes  
to a more defined and spacious soundstage. When using the balanced XLR input connections, 
set the input’s corresponding Balanced/Unbalanced selector switch to the Balanced position.

Where should I set the Left and Right gain controls?

In most cases you will simply leave the Left and Right knobs fully clockwise where they are 
completely out of the audio circuit. If you do need to compensate for speaker placement or room 
acoustics lower one of the controls until the volume level of the left and right speakers are equal.

WARRANTY REPAIR

Call your Parasound dealer first. If the dealer can’t help you with your problem we encourage you 
to call Parasound’s Technical Service Department, toll-free at 

1-866-770-8324

, Monday – Friday, 

8am – 4pm Pacific time. We can suggest other diagnostic tests you can easily perform. 
If we determine that your JC 2 should be returned to Parasound or an Authorized Parasound 
Warranty Center for inspection and possible servicing, we will provide the location of a warranty 
center near you or shipping instructions for the unit’s return to Parasound.

Before You Return Any Unit to Parasound for Service

Before you send your unit to Parasound, you will need to obtain a specific Return Authorization 
(RA) number and shipping instructions from Parasound’s Technical Department. The RA number 
must be clearly marked on the outer carton. Use the original factory packing materials and  
arrange adequate insurance to cover its value. You must include a copy of your purchase receipt, 
since this document establishes the validity of this unit’s warranty. Warranty repairs are only 
performed by Parasound or Parasound Authorized warranty centers when your purchase receipt 
is from a Parasound Authorized Dealer or Parasound Authorized Reseller.

Units Will Be Refused by Parasound Under the Following Conditions:

1. Unit was sent without the Parasound-assigned RA number marked on the carton.
2. Unit was sent in an unsuitable shipping carton, likely to have been damaged in transit.
3. Unit has inadequate packing, unit likely to have been damaged in transit.
4. Unit was shipped collect for shipping charges. We do not accept collect shipments.
5. Unit was shipped via the US Postal Service.
6. Unit was sent to an address other than the address instructed by our Technical Department.

Note:

 The shipping address is not the same as Parasound’s office address.

Warranty Repair

Read your accompanying Parasound Limited Warranty carefully to understand the applicable rights 
and limitations. This section provides instructions for obtaining repairs, both for units covered 
under the Parasound Limited Warranty and for units or situations which are outside the Warranty.
Unit is not eligible for repair under the terms of the Parasound warranty if:
1. Unit was not purchased from a Parasound Authorized Dealer.
2. You are not the original owner. The Parasound warranty is not transferable.
3. Unit’s serial number was removed, modified, or defaced.
4. Unit shows evidence of abuse and/or misuse. 
5. Unit was modified in any way.
6. A prior repair was attempted by an unauthorized repair station.

FREQUENTLY ASKED QUESTIONS continued/ WARRANTY

Содержание Halo JC 2

















Отзывы: