manualshive.com logo in svg

Parametric TCR, Руководство пользователя

Поделиться
Скачать
Parametric TCR Скачать руководство пользователя страница 8

Important: These settings will need to be changed depending on where the radar
is installed, what you are trying to detect and the type of vehicles likely to pass
underneath.

Radar Settings

Radar Enabled

Radar on by default

Channels

1 set by default

2 if you have a radar in the same

Sensitivity

After entering 

LTRDist

 and 

RTLDist

 the sensitivity is automatically determined

based on those values. The further the distance to the measurement, the higher the
sensitivity.

Note: Small adjustments of sensitivity can be done manually. If the ratio (sensitivity
vs. RTL/LTR) is not correct, the radar may incorrectly categorize the measured
object.

Beam Angle

Beam size from left to right

Note: In areas where you may have obstacles in the way, you may need to narrow
the angle of the beam.

Beam Directions

Can be offset by up to 30 degrees in any direction. Once again cater for things link
tree and things in the way.

LTRDist

Distance between the radar surface and the object you are trying to detect
approaching from the left.

LTRDist

Содержание TCR



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды