Parajet Volution Compact Скачать руководство пользователя | Manualshive

Страница: 11 / 27

background image

CHARGING THE STARTER BATTERY

Every Volution should arrive with the battery installed in position and ready charged. Do not
however expect the battery to be fully topped up at the time of shipping. For this reason it is
advised that you top up your starter battery before attempting to fly your Volution.

USE THE PARAJET CHARGER SUPPLIED WITH YOUR UNIT

Note:

When your Volution is being flown regularly it will not be necessary to charge the battery

as the in-built generator charges it automatically.
However, if you do not fly your Volution for more than

4 weeks

your battery will require

charging, simply plug the Parajet charger into the charging socket on your power unit for a
minimum of 24 hours

1. To remove the battery, simply unlock the harnesses upper retaining bar from the chassis. Fold the
harness down away from the body of the power unit to expose the electronics case.
2. Remove the case cover by hinging the top out first, the bottom can then be pulled up and out of
position.
3. The battery will now be exposed at the base of the electronics box. The positive terminal is insulated
with a press-fit rubber boot. This must be pulled back to expose the terminal that must be disconnected.
4. Disconnect both terminals before removing the battery.
5. IMPORTANT: When you replace the battery be sure to push the insulating boot firmly over the positive
terminal. Failure to do so will cause the battery to short out on the body of the machine which could

result in fire or damage

.

Open Electronics Case

Battery Position

7

«
...
9
10
11
12
13
...
»

Содержание Volution Compact




























Отзывы:

Нет отзывов

Похожие инструкции для Volution Compact

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды