manualshive.com logo in svg

Paradyne TNE1500-P, Руководство по установке

Поделиться
Скачать
Paradyne TNE1500-P Скачать руководство пользователя страница 9

9

Connect the Ethernet Line

The 10/100 Ethernet Port auto-negotiates speed and duplex mode in accordance with 
the remote equipment to which it is connected; Ethernet speed and duplex mode 
configurations cannot be set on the TNE1500. For the best connection results, the 
remote device (PC, hub, switch, etc.) should be set to auto-negotiate speed and duplex 
mode as well. If the remote device cannot be configured to auto-negotiate, speed may 
be set at either 10 Mbps or 100 Mbps but duplex mode must be set to Half Duplex; a 
10/100 Ethernet connection will not operate properly if the remote device is set to Full 
Duplex.

Plug the Ethernet cable into the 10/100 Ethernet Port on the back of the TNE1500. 
Verify the connection: solid green illumination of the 10/100 Ethernet Connection Lnk 
(Link) LED on the front of the TNE1500 indicates a connection has been established. If 
the Ethernet Lnk LED is illuminated, but not the Ethernet 100 LED, then a 10 Mbps 
connection has been established. If the Ethernet Lnk AND 100 LEDs are both 
illuminated, then a 100 Mbps connection has been established.

For most applications, the TNE1500 connects to a PC using a straight-through Ethernet 
cable and to a hub or a switch using a crossover Ethernet cable. For any other 
connection combinations you must verify the pinout of the Ethernet device to which you 
are connecting the TNE1500 in order to determine which type of cable is required.

     

Table 9. Ethernet Pinouts

Pin

Function

Pin 1

Rx+

Pin 2

Rx–

Pin 3

Tx+

Pin 4

not used

Pin 5

not used

Pin 6

Tx–

Pin 7

not used

Pin 8

not used

Содержание TNE1500-P

















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды