Paradyne SMD2000-24E Скачать руководство пользователя страница 26

26

Technical Specifications

Table 14. SMD2000-24E Technical Specifications

Specification

Criteria

Bandwidth and Distance 
Capabilities – SHDSL 
Ports

Default is 272 kbps at up to 20,200 ft (6,157 m)

Maximum distance is up to 24,000 ft (18,000 m) at 
144 kbps

Maximum bandwidth is 2320 kbps at up to 11,300 ft 
(3,444 m)

Bandwidth and Distance 
Capabilities – E1 Uplinks

Maximum bandwidth is 1,984 kbps with all 31 timeslots

Maximum distance is 5,000 ft (1,524 m)

Compliance

EMC:  FCC Part 15; CSA/C108.8; EN55022; EN55024

Safety:  UL 1950, CSA C22.2 No. 950; EN60950

CE Marking

Environment

Operating Temperature: –40° F to 149° F (–40° C to 
65° C)

Storage Temperature: –40° F to 158° F (-40° C to 70° C)

Humidity: 5 % to 95 %, Non-condensing

Altitude: –200 ft to 16,500 ft (–60 m to 5,000 m)

Interfaces

24  SHDSL ports (1 RJ21 50-pin Telco)

2  fixed RJ45 E1 uplink ports

1  RJ45 10/100BaseT management interface

1  RJ45 RS-232 COM port

2  Uplink Interface Module (UIM) slots supporting 
10/100BaseT, E1, and T1

Power

–48V DC

1 amp minimum / 1.6 amp maximum
(Actual power draw depends on chassis configuration)

Size

1.75" High x 17" Wide x 14" Deep
(4.4 cm High x 43.2 cm Wide x 35.6 cm Deep)

Weight

12.5 lbs (5.73 kg)

Содержание SMD2000-24E





























Отзывы: