background image

 19

8784-A2-GZ40-20

February 2001

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor
directly for any help needed. For additional information concerning warranty,
sales, service, repair, installation, documentation, training, distributor locations, or
Paradyne worldwide office locations, use one of the following methods:

H

Internet:  Visit the Paradyne World Wide Web site at www.paradyne.com.
(Be sure to register your warranty at www.paradyne.com/warranty.)

H

Telephone:  Call our automated system to receive current information by fax
or to speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail
them to Technical Publications, Paradyne Corporation, 8545 126th Ave. N.,
Largo, FL 33773, or send e-mail to [email protected]. Include the
number and title of this document in your correspondence. Please include your
name and phone number if you are willing to provide additional clarification.

Trademarks

Hotwire is a registered trademark of Paradyne Corporation. All other products
and services mentioned herein are the trademarks, service marks, registered
trademarks or registered service marks of their respective owners.

Copyright 

E

 2001 Paradyne Corporation. Printed in U.S.A.

Содержание Hotwire 8784




















Отзывы: