background image

 10

!

Important Safety Instructions

1. Read and follow all warning notices and instructions marked on the product or

included in the manual.

2. Slots and openings in the cabinet are provided for ventilation. To ensure reliable

operation of the product and to protect it from overheating, these slots and
openings must not be blocked or covered.

3. Do not allow anything to rest on the power cord and do not locate the product

where persons will walk on the power cord.

4. Do not attempt to install or service this product yourself, as opening or removing

covers may expose you to dangerous high voltage points or other risks. Refer all
installation and servicing to qualified service personnel.

5. General purpose cables are provided with this product. Special cables, which may

be required by the regulatory inspection authority for the installation site, are the
responsibility of the customer.

6. When installed in the final configuration, the product must comply with the

applicable Safety Standards and regulatory requirements of the country in which it
is installed. If necessary, consult with the appropriate regulatory agencies and
inspection authorities to ensure compliance.

7. A rare phenomenon can create a voltage potential between the earth grounds of

two or more buildings. If products installed in separate buildings are
interconnected, the voltage potential may cause a hazardous condition. Consult a
qualified electrical consultant to determine whether or not this phenomenon exists
and, if necessary, implement corrective action prior to interconnecting the products.

8. In addition, if the equipment is to be used with telecommunications circuits, take

the following precautions:

— Never install telephone wiring during a lightning storm.

— Never install telephone jacks in wet locations unless the jack is specifically

designed for wet locations.

— Never touch uninsulated telephone wires or terminals unless the telephone

line has been disconnected at the network interface.

— Use caution when installing or modifying telephone lines.

— Avoid using a telephone (other than a cordless type) during an electrical

storm. There may be a remote risk of electric shock from lightning.

— Do not use the telephone to report a gas leak in the vicinity of the leak.

Содержание Hotwire 8747












Отзывы: