background image

13

10.

This unit is provided with a replaceable lithium battery. Replace the battery only with 
the same type recommended by the manufacturer. Discard used batteries 
according to the manufacturer’s instructions.

Supplier’s Declaration of Conformity

Place of Issue: Paradyne Corporation

8545 126

th

 Avenue North

Largo, FL 33773-1502
USA

Date of Issue:

4/4/2003

Paradyne Corporation, located at the above address, hereby certifies that the Hotwire® 
Model Number 8300-AX-400, bearing labeling identification number 
US:AW2DLNAN8300-AX complies with: the Federal Communications Commission's 
("FCC") Rules and Regulations 47 CFR Part 68, the Administrative Council on Terminal 
Attachments ("ACTA")-adopted technical criteria: TIA-968-A, "Telecommunications - 
Telephone Terminal Equipment -Technical Requirements for Connection of Terminal 
Equipment To the Telephone Network, October 2002" and T1.TRQ.6-2001, "Technical 
Requirements for SHDSL, HDSL2, HDSL4 Digital Subscriber Line Terminal Equipment 
to Prevent Harm to the Telephone Network."

Patrick Murphy

Senior Vice President, Chief Financial Officer

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for 
any help needed. For additional information concerning warranty, sales, service, repair, 
installation, documentation, training, distributor locations, or Paradyne worldwide office 
locations, use one of the following methods:

Internet:

 Visit the Paradyne World Wide Web site at 

www.paradyne.com

. (Be 

sure to register your warranty at 

www.paradyne.com/warranty

.)

Telephone:

 Call our automated system to receive current information by fax or to 

speak with a company representative.

Within the U.S.A., call 1-800-870-2221

Outside the U.S.A., call 1-727-530-2340

Содержание Hotwire 8300

















Отзывы: