Paradyne Hotwire 6351 Скачать руководство пользователя страница 17

17

4. Do not attempt to service this product yourself, as opening or removing covers may 

expose you to dangerous high voltage points or other risks. Refer all servicing to 
qualified service personnel.

5. General purpose cables are used with this product for connection to the network. 

Special cables, which may be required by the regulatory inspection authority for the 
installation site, are the responsibility of the customer. Use a UL Listed, CSA 
certified, minimum No. 24 AWG line cord for connection to the Digital Subscriber 
Line (DSL) network.

6. When installed in the final configuration, the product must comply with the 

applicable Safety Standards and regulatory requirements of the country in which it 
is installed. If necessary, consult with the appropriate regulatory agencies and 
inspection authorities to ensure compliance.

7. A rare phenomenon can create a voltage potential between the earth grounds of 

two or more buildings. If products installed in separate buildings are 
interconnected, the voltage potential may cause a hazardous condition. Consult a 
qualified electrical consultant to determine whether or not this phenomenon exists 
and, if necessary, implement corrective action prior to interconnecting the products.

8. Input power to this product must be provided by one of the following: (1) a UL 

Listed/CSA certified power source with a Class 2 or Limited Power Source (LPS) 
output for use in North America, or (2) a certified transformer, with a Safety Extra 
Low Voltage (SELV) output having a maximum 240 VA available, for use in the 
country of installation.

9. In addition, since the equipment is to be used with telecommunications circuits, take 

the following precautions:

Never install telephone wiring during a lightning storm.

Never install telephone jacks in wet locations unless the jack is specifically 
designed for wet locations.

Never touch uninsulated telephone wires or terminals unless the telephone line 
has been disconnected at the network interface.

Use caution when installing or modifying telephone lines.

Avoid using a telephone (other than a cordless type) during an electrical storm. 
There may be a remote risk of electric shock from lightning.

Do not use the telephone to report a gas leak in the vicinity of the leak.

CANADA – EMI NOTICE:

!

This Class B digital apparatus meets all requirements of the Canadian 
interference-causing equipment regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du 
règlement sur le matérial brouilleur du Canada.

Содержание Hotwire 6351





















Отзывы: