background image

TM

 1

Hotwire

 5546 RTU Customer Premises

Installation Instructions

Document Number 5546-A2-GN10-00

September 1998

Before You Begin

The Hotwire

 5546 RTU (Remote Termination Unit) interoperates with the Hotwire

8546 DSL Card in the DSLAM system. Verify that the 8546 DSL card has Firmware
Release 2.2 or higher.

An optional POTS (Plain Old Telephone Service) splitter is available for the Hotwire
5546 RTU. When a POTS splitter is installed, the telephone and 5546 RADSL (Rate
Adaptive Digital Subscriber Line) RTU can function at the same time over the same pair
of copper wires. In order to confirm the RTU installation, the POTS splitter should be
installed first.

To install a POTS splitter, refer to the appropriate POTS splitter document:

Document Number

Document Title

5030-A2-GN10

Hotwire 5030 POTS Splitter Customer Premises 
Installation Instructions

5038-A2-GN10

Hotwire 5038 Distributed POTS Splitter Customer
Premises Installation Instructions

Contact your sales or service representative to order additional product documentation.
Paradyne documents are also available on the World Wide Web at:

http://www.paradyne.com

Select 

Service & Support 

 Technical Manuals

Package Checklist

Verify that your package contains the following:

Model 5546 Remote Termination Unit (RTU)

DSL interface cable with RJ11 connectors

RJ45 to DB9 adapter plug (Part No. 002-0093-0031)

One ferrite choke (Model 5546-A1-200 only)

Power cord with power transformer

Warranty card

Содержание Hotwire 5546
























Отзывы: