Paradyne FrameSaver 9120 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 82

background image

About the FrameSaver 9120

1-3

9121-A2-GB20-20

May 1998

What You Need to Do Before Using the
FrameSaver 9120

-

Subscribe to ISDN service if using an ISDN BRI DBM.

-

Get DLCI numbers and CIR from the Network Service Provider.

-

Modify network design to include FrameSaver access units (for examples,
see Chapter 3,

Typical Applications in the FrameSaver 9120 Technical

Reference).

-

Define IP addressing scheme, with an IP address assigned to the
FrameSaver access unit, and IP addresses and subnet masks added to
configuration worksheets (for IP addressing examples, see Chapter 2,
Management Control and IP Addressing and for configuration worksheets,
see Appendix B,

Configuration Worksheets, in the FrameSaver 9120

Technical Reference).

-

Install ISDN BRI DBM, if ordered separately (see the

ISDN BRI Dial Backup

Unit (DBM), Installation Instructions).

-

Install FrameSaver access unit, ready to be configured (see the

1-Slot

Assembled Access Unit, Installation Instructions).

-

Determine the configuration shortcuts to be used

before the network cable is

connected (see Chapters 1, 3, and 4 of the

FrameSaver 9120 Technical

Reference for additional information).

-

Complete configuration worksheets for configuring the FrameSaver
access unit (see Appendix B,

Configuration Worksheets, of the FrameSaver

9120 Technical Reference).

«
...
11
12
13
14
15
...
»

Содержание FrameSaver 9120



















































































Отзывы:

Нет отзывов

Похожие инструкции для FrameSaver 9120

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 20

Бренд: Daktronics Страницы: 5

Бренд: Daikin Страницы: 12

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: Jabra Страницы: 8

Бренд: Pando Страницы: 43

Бренд: Vaillant Страницы: 12

Бренд: LOGICDATA Страницы: 23

Бренд: NCE Страницы: 4

RISC Module SOM-A2552

Бренд: Advantech Страницы: 40

Apollo 70-600 Series

Бренд: Conbraco Industries Страницы: 4

Бренд: Ravel Страницы: 33

Бренд: Hansen Страницы: 4

TRILOGY T500 Series

Бренд: Eclipse Страницы: 20

MotorController WCC 310 UL

Бренд: Window Master Страницы: 39

Бренд: salmson Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды