Paradyne COMSPHERE 3821Plus Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 28

background image

3

Cable the NIM

Connect one end of the short ribbon cable to the 50-pin connector at the bottom of the
NIM. Connect the other end to P21 (on the right side of the carrier) or P22 (on the left
side of the carrier).

Connect a network interface cable to the 50-pin connector in the middle of the NIM.
Connect the other end to the dial or leased-line interface. This may be an RJ11 gang
box or a 66A-punchdown block.

495-14798

NETWORK INTERFACE

CABLE

P21 or P22

SHORT

RIBBON

CABLE

A 2-wire leased line connection to a JM8 interface requires a 6-position to 8-position
crossover cable, such as Paradyne Part Number 3000-F1-006, as shown in the
following diagram. See the User’s Guide for further information.

«
...
3
4
5
6
7
...
»

Содержание COMSPHERE 3821Plus





























Отзывы:

Нет отзывов

Похожие инструкции для COMSPHERE 3821Plus

Бренд: E-Lins Страницы: 4

WEBR@CER 852 PSTN

Бренд: Topcom Страницы: 38

Бренд: Kyocera Страницы: 11

Бренд: iRZ Страницы: 19

Бренд: Eaton Страницы: 83

Бренд: ZyXEL Communications Страницы: 70

Бренд: NetComm Страницы: 139

Бренд: Zte Страницы: 15

Бренд: ELSA Страницы: 46

Бренд: Dynex Страницы: 8

Бренд: Ebyte Страницы: 31

3CP5610A - U.S. Robotics 56K V90 PCI Performance Pro Faxmodem Dos/NT/Linux

Бренд: 3Com Страницы: 100

Бренд: 3Com Страницы: 101

Бренд: Hughes Страницы: 61

Бренд: Racal-Vadic Страницы: 98

Бренд: Raymar Страницы: 2

Бренд: Zte Страницы: 27

Бренд: Option Audio Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды