manualshive.com logo in svg

Paradyne 9161 Single T1, Руководство пользователя

Поделиться
Скачать
Paradyne 9161 Single T1 Скачать руководство пользователя страница 215

Troubleshooting

 9-33

9161-A2-GH30-40

April 1999

Digital Loopbacks

A Digital Loopback loops the digital voice signal received from the T1 interface
back to the same interface, just before reaching the D-to-A converter on the voice
port.

496-15200

to: T1 Interface

Digital Loopback

CODEC

D to A

Converter

The following tests cannot be running when a digital loopback test is initiated:

Analog Loopback, DRS or Quiet Test Tone on the same port

Analog Loopbacks

An Analog Loopback loops the analog voice signal received from the T1 interface
back to the same interface, after passing through the Digital-to-Analog converter
and Analog-to-Digital converter on the voice port.

496-15201

to: T1 Interface

Analog Loopback

CODEC

D to A

Converter

The following tests cannot be running when an Analog Loopback test is initiated:

DRS or Quiet Test Tone, or Digital or Line Loopback on the same port

Содержание 9161 Single T1





































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды