Paradyne 9109 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 8

Paradyne 9109 Скачать руководство пользователя страница 3

496-15149

PO

RT 4

9109 Sync

PO

RT 3

Port 1

Port 2

Port 3

Port 4

97-15167-01

PO

RT 2

PO

RT 1

3

!

HANDLING PRECAUTIONS FOR STATIC-SENSITIVE DEVICES

This product is designed to protect sensitive components from
damage due to electrostatic discharge (ESD) during normal
operation. When performing installation procedures,
however, take proper static control precautions to
prevent damage to equipment. If you are not sure
of the proper static control precautions, contact
your nearest sales or service representative.

Installing the I/O Card

The 4-port I/O card provides the APM with DTE connections. The I/O card inserts
directly behind the APM that it supports. Slot numbers are identical to facilitate correct
installation.

1. Remove the I/O card from the shipping box. Handle only by

the top and bottom edges to avoid damaging the card.

2. At the rear of the housing, align the I/O card with the upper

and lower tracks of the slot. Push gently towards the
midplane until it stops and you cannot push the card any
further.

98-15150-02

Rear View

Screws

5-Slot

2-Slot

3. There are two captive screws on the I/O card. Using a

small, flat-blade screwdriver, alternately tighten each screw
until both are snug.

«
1
2
3
4
5
...
»

Содержание 9109









Отзывы:

Нет отзывов