Paradigm Connect100 Скачать руководство пользователя страница 2

Страница: 2 / 20

- 2 -

Paradigm

The information in this document has been carefully compiled and checked for technical

accuracy. Paradigm Communication Systems Ltd. accept no liability for inaccuracies or errors. In

line with the company policy of technical advancement, the information within this document may

be changed. The user should ensure that the correct issue of the document is used.

Paradigm assumes no responsibility for the use of this document if any unauthorised changes to

the content or format are made.

This document is provided without implied or expressed warranty of any kind, including but not

limited to the implied warranties of merchantability and fitness for purpose.

Other manufacturers’ registered trademarks and trade names which appear in this document are

hereby acknowledged.

Comments or correspondence regarding this document should be addressed to:

Paradigm Communication Systems Limited

Paradigm House

14 Wilsom Road

Alton, Hampshire

GU34 2PP

England

Tel:

+44 (0) 1420 88199

Fax:

+44 (0) 1420 88842

Email: [email protected]

No part of this document may be reproduced in any form without the prior written consent of

Paradigm Communication Systems Limited. Use of the information contained herein is strictly

reserved for Paradigm Communication Systems Limited. Other use in any form and/or by any

means whatsoever is strictly prohibited.

DN:

ED-IMA-02397

Rev:

Release Date: 17/07/2015

Legal

Safe Use

WARNING

Radiation Hazard. Transmitter power levels are sufficient to cause blindness or other serious

injury to body tissue. Do not power on the PIM and Transceiver until it is safe to do so.

The equipment described in this manual is intended to be installed, used and operated only

for the purpose for which it was designed, in accordance with the safety procedures and any

other instructions given in this manual. Nothing stated in this manual reduces the professional

responsibilities of users for the exercise of sound judgement and best practice.

WARNING

Risk of Electric Shock. High voltages exist within the units and the cables providing power to

the units. Always remove power from these devices when performing maintenance. Do not

modify power cables or physical unit in any way.

WARNING

This equipment is intended for installation in a restricted access location. The equipment

should not be touched during operation.

Содержание Connect100





















Результаты поиска

Содержание Connect100

Отзывы:

Похожие инструкции для Connect100

Бренды по названию

Популярные бренды

Paradigm Connect100, Руководство по установке

Результаты поиска

Содержание Connect100

Отзывы:

Похожие инструкции для Connect100

Бренды по названию

Популярные бренды