background image

7

art.nr

.8822165, Rev

. 2022-04 Publ. 2022-04-1

1

Panthera 

AB reserves the right to make technical changes if required

SAFETY REGULATIONS

Lifting while the user is in the wheelchair 

(Fig. 3)

If the wheelchair is to be lifted while the user remains seated, always grip the chair’s chas-

sis. See arrows in  

Fig. 3

Do not lift using the push handles, wheels or other movable sections.

Wheelchair technique – Ramps and sloping surfaces

Driving up ramps and sloping surfaces 

(Fig. 4)

When you are going to drive up a ramp, you need to take a bit of a run-up, keep a steady 

speed and at the same time control your direction. Lean your upper body forwards and 

move both rear wheels with fast, powerful pushes.

Driving down sloping surfaces 

(Fig. 5)

When driving down sloping surfaces and slopes, it is important that you have control over 

your direction and speed. Lean back and allow the rear wheels to move slowly through 

your hands. You should be able to stop the wheelchair at any time by grasping the rear 

wheels.

Warm or cold surfaces

If the wheelchair is exposed to sunshine for long periods, its surfaces may become extre-

mely warm. The wheelchair´s surfaces can also become very cold if is stored or used in 

cold conditions.

Fig. 3

Fig. 4

Fig. 5

Содержание G515























Отзывы: