background image

INSTALLATION INSTRUCTIONS     CM296A

 © Panduit Corp. 2004

For Technical Support: www.panduit.com/resources/install_maintain.asp

Industrial Automation Enclosure

Part Number: IAEIP66, IAEFK54

Page 1 of 5

(view shown with door removed)

List of Components:

(1) 24 VDC Power Supply
(3) T

AK

-T

YS

(6) Adhesive Backed Mounts
(6) P

AN

-T

YS

(1) Electrical Hole Seal
(1) Port ID Label
(3) 10 AWG Grounding Cables
(1) 12 AWG Grounding Cable
(1) 35mm DIN Rail
(1) #10-32 x 1/2" Pan Head Screw
(3) #10 Spring Lock Washer
(2) #10-32 Hex Nut

IAEIP66

35mm DIN Rail

Cover Plates for Fan
and Exhaust Filter
Openings

Opening for 1/2"
Conduit Fitting

Opening for Industrial
Enclosure Gland Plate

Inner Panel

Important Notice:

                             Should Fan Kit P/N IAEFK54 be integrated into the enclosure, P/N IAEIP66, the IP rating of the enclosure 

shall be reduced to IP54. If the enclosure and any active equipment is located in an environment containing conductive 
particles that have the potential to cause sparks and shorts, or the enclosure is placed in an environment that contains 
ignitable dust or explosive gases, in this scenario the IP rating of the enclosure shall be reduced to IP44. Before any 
application in these last cases, the installer should insure that all requirements, legal and industry, are met and 
precautions are taken to meet the installation requirements of the equipment placed inside the enclosure. 

Содержание IAEIP66






Отзывы: