Panasonic WX-CH450, Руководство по эксплуатации

Страница: 9 / 49

9
Power indicator
The indicator shows the status as follows.
Green: Power is supplied and the unit is operating.
Green blinking: Power is supplied and manager mode is
activated.
Red: The battery is almost exhausted. Replace the
battery with a charged one.
Red blinking: An error has occurred.
Phone button [R]
This function is activated only when this product is set to
manager mode.
For details on how to use this button, contact the sales
shop where you bought this product.
Alert button [F]
Functions vary depending on the Center Module to which
the user is connected.
<When connected to WX-CC411, WX-CC412>
Hold down this button for 2 seconds or more to send a
security alert to the Center Module.
The action taken when an Alert is sent depends on the
Center Module setting, and can include “TALK & PAGE
Recording”, “Send E-mail”, etc.
<When connected to WX-C3010>
The [F] button functions as the external device control
button. While it is pressed, an external device is kept ON.
Volume control buttons [VOL + – ]
Pressing the buttons will increase or decrease the sound
level.
Press the [+] button to increase the sound level. Each
time the button is pressed, a beep notifies the user that
the volume is being increased. If you try to increase the
volume over the upper limit, two beeps notify the user of
a prohibited action.
Press the [–] button to reduce the sound level. Each time
the button is pressed, a beep notifies the user that the
volume is being reduced. If you try to reduce the volume
below the lower limit, two beeps notify the user of a
prohibited action.
When the product’s power is turned off and then turned
back on, the volume will return to the default setting
(center value).
Talk 1 button [T1]
This button controls communications with the customer.
The function of this button changes depending on the DIP
switch setting. (Refer to p. 20 “DIP switch setup”.)
<For Direct Lane Select setup in Press-To-Talk (PTT) mode>
While the [T1] button is being pressed, you can talk with
a customer at the Lane A menu board.
<For Normal setup in Press-To-Talk (PTT) mode>
While the [T1] button is being pressed, you can talk with
a customer at the menu board of the connected lane.
<For Direct Lane Select setup in Talk-Lock mode>
When you press the [T1] button once, you can talk with
a customer at the Lane A menu board. Press the button
again to end the call.
<For Normal setup in Talk-Lock mode>
When you press the [T1] button once, you can talk with a
customer at the menu board of the connected lane. Press
the button again to end the call.
Talk 2 / A/B lane selection button [T2, A/B]
This button’s operation differs depending on the operation
of the button at startup.
Normal setup: Turn on the power pressing the [POWER]
button for 1 second or more while holding down the [T1]
button.
Direct Lane Select setup: Turn on the power pressing the
[POWER] button for 1 second or more while holding down
the [T2] button.
p
The [T2] button’s operation remains unchanged
unless this product is initialized or the setting is
changed.
As the factory setting, this product starts up at the
“Normal setup”.
Note
<For Direct Lane Select setup in Press-To-Talk (PTT) mode>
While the [T2] button is being pressed, you can talk with
a customer at the Lane B menu board.
<For Direct Lane Select setup in Talk-Lock mode>
When you press the [T2] button once, you can talk with
a customer at the Lane B menu board. Press the button
again to end the call.
<For Normal setup>
When the [T2] button is pressed once, the lane for dual
lane operation is switched from lane A to lane B (or vice
versa). It can be switched only when the WX-CC412
Center Module is used.
Page button [P]
This button controls communications with store
personnel.
<When the Press-To-Page (PTP) mode is preset>
While the [P] button is held down, you can speak to store
personnel.
<When the Page-Lock mode is preset>
When you press the [P] button once, you can speak to
the store personnel until you press the button a second
time.
English