-15-
*
When using the Unit Number 1 to
9
6 setting, the unit number setting needs to be configured using the RS485 SET UP menu. For details
about configuring this setting, see step 2 and page 21.
*
Turning on power when this setting is selected causes the RS485 SET UP menu to appear during the initialisation routine.
1
2
3
4
ON
5
6
7
8
DIP Switch 1
Unit
Number
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
DIP Switch 1
Unit
Number
DIP Switch 1
Unit
Number
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
■
RS485 Communication Parameters (DIP Switch 1)
Configuring DIP Switch 1 as shown below resets communication parameters to their factory default settings. You can
then change the settings as desired.
1
2
3
4
ON
5
6
7
8
DIP Switch 1
Setting Description
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
1
2
3
4
ON
5
6
7
8
This setting resets communication parameters to the factory default settings.
BAUD RATE : 19 200 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
BAUD RATE : 9 600 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
BAUD RATE : 4 800 bit/s, DATA BIT : 8 bit, PARITY CHECK : NONE, STOP BIT : 1 bit
ON
Perform the following steps to use this setting.
(1) Turn off the camera and use DIP Switch 1 to configure RS485 communication parameters as shown above.
(2) Turn on the camera.
This applies the setting you configured in step (1).
(3) Turn off the camera, use DIP Switch 1 to set the unit number (pages 14 and 15), and then turn the camera
back on again.
WV-CW960G̲CW964E̲US 08.12.4 10:49 AM ページ15
