manualshive.com logo in svg

Panasonic WV-CP474E, Руководство по эксплуатации, Страница: 4 / 12

Поделиться
Скачать
Panasonic WV-CP474E Скачать руководство пользователя страница 4

Mounting the Lens

Note:

Before you mount the lens, loosen the screw on the side of the camera, and rotate the

ring clockwise until it stops.
If the ring is not at the end, the inner glass or CCD image sensor may be damaged.

1. Mount the lens by turning it clock-

wise on the lens mount of the cam-
era.

Note:

When mounting the C-mount

lens on the camera, mount the
C-mount adapter by turning it
clockwise in advance.

2. Connect the lens cable to the auto

iris lens connector on the side of
the camera.

Flange-back Adjustment

1. Loosen the flange-back fixing screw on the flange-back adjusting ring.

2. Turn the flange-back adjusting ring to obtain a focused point while watching the monitor

screen.

3. Tighten the flange-back fixing screw on the flange-back adjusting ring.

Caution:

Tightening the screw by force will cause damage to the screw or deviation of

focus.

Note:

The object may be out of focus when using a source of near-infrared light than

using the visible light.

Caution for Mounting the Lens

Follow the indication shown in the figure for the protrusion between a lens and the camera
body. This camera wears mount for use with the CS-mount lens at the factory shipment.
Use the optional C-mount adapter WV-AD20E when using the C-mount lens.
The lens less than 450 

g

(0.99 lbs) can be mounted on the camera. If the lens is heavier,

both the lens and camera should be
secured by the supporter.

C-mount:

Less than 13 mm (1/2”)

CS-mount: Less than 8 mm (5/16”)

MOUNTING LENS/FOCUS ADJUSTMENT

• Mounting from the Top

Remove the mount adapter from the bottom of the camera by removing the two fixing
screws.  Attach the mount adapter to the top as shown in the figure, then mount the
camera on the mounting bracket.

Make sure that the two original fixing
screws are used when mounting the
mount adapter as longer length screws
may damage inner components, or
shorter type screws may cause the
camera drop.

INSTALLATION OF CAMERA

WV

-

CP47

0

CP470

CP470

Flange-back
Fixing Screw

Flange-back
Adjusting Ring

Installation of Auto Iris Lens Connector

Install the lens connector (YFE4191J100) when using a video drive ALC lens.

(1) Cut the iris control cable at the edge of the lens connector to remove the existing lens

connector and then remove the outer cable cover as shown in the figure below.
The pin assignment of the lens connector is as follows:
Pin 1: Power source; +9 V DC, 50 mA max.
Pin 2: Not used
Pin 3: Video signal; 0.7 V[p-p]/40 k

Ω

Pin 4: Shield, ground

(2) Solder the lens cable to the pins of the

supplied connector.

Pin 3 

Pin 4

Pin 2

Rib

Pin 1 

C-mount Adapter
(Option)

CP470

WV-

CP470

CP470

Fixing Screws

Mount Adapter

Lens Mount

Содержание WV-CP474E













Отзывы:

Нет отзывов