manualshive.com logo in svg

Panasonic Workio DP-C265, Руководство по обслуживанию

Panasonic Workio DP-C265 - Многофункциональное устройство для офиса с возможностью печати, сканирования и копирования документов. Для использования нужно скачать и прочитать Руководство по эксплуатации, которое можно скачать бесплатно с manualshive.com. Необходимый ресурс для правильной настройки и работы с устройством.

Поделиться
Скачать
background image

184

 FEB 2008

Ver. 1.1

DP-C405/C305/C265

3.1.5.

Data Security Precautions

1. The Service Mode Password is essential to maintaining the security of the machine. 

Service technicians must change the factory default password using the Service Mode 

“F7-14: 

Service Mode Password”

, record the new password and store it in a safe place out of the reach of 

others. (Refer to the Service Manual Section 5.1.7. )

2. The Service Mode is used by service technicians to perform maintenance and/or repairs, as well as to 

maintaining security of the machine. Service technicians must not leave the machine in the Service 
Mode after servicing the unit.

3. Before servicing, make sure the customer's SD Memory Card or the External Memory Card is removed 

from the machine.

4. Service technicians are required to keep the SD Memory Card including the Firmware in a confidential 

and safe place. Make certain to remove the SD Memory Card from the machine, if it was used for 
updating the Firmware, etc.

5. Before servicing the unit, back up the machine's data to prevent losing the settings.

a. Back up the settings data onto an SD Memory Card using the Service Mode 

“F9-11: Param 

Backup to SD”

.

b. Back up the settings data onto a PC via a Network using 

“Network Configuration Editor”

.

c. Print out the Service Parameters.

6. Service Technicians are required to keep the SD Memory Card including the machine and the 

customer's information confidential and in a safe place.

7. When disposing/transferring this machine, delete all of the customer's information.

a. Delete the Hard Disk Drive data by initializing the Hard Disk Drive as follows:

Press 

“Function” 

->

”General Settings”

 -> 

“09 Key Operator Mode”

 -> 

“34 Hard Disk 

Initialize”

.

b. Delete the data in the F-ROM using the Service Mode 

“F9-06-03: Shipment Set”

.

c. Delete the data in the SD Memory Card on the SC PCB. Physically break the SD Memory Card or 

completely delete the data using a data deleting software.

8. To secure the customer's information, make sure the Fax number/E-mail address is set correctly in the 

Check & Call feature.

9. Service Manuals, and Installation Instructions are essential to maintaining the security of the machine. 

Service technicians are required to keep the customer's information confidential and in a safe place. 

10. When the SC PCB is replaced the MAC address will be different, make sure that the new MAC address 

is recognized on the Network.

11. When setting the Remote Registration function, there is a slight possibility of an unauthorized third 

party attempt to access your machine's settings using an E-mail function through the Firewall. When 
using this function, we recommend configuring your network environment with a switching hub, and 
encryption to prevent your device from being wiretapped.

12. When moving the machine for repair, etc. there is a remote possibility that the stored data can be 

vulnerable to unauthorized access, or get corrupted. Convey this to the customer and obtain their 
permission to Back up the data onto an SD Memory Card or a PC, and then delete it from the machine.

13. While servicing the machine, it is imperative that the customer's data is maintained in strictest 

confidentiality to prevent security breach.

14. Delete the customer's data from the replaced/replacement machine or Hard Disc Drive to maintain 

security of the machine.

15. After repairs are completed, restore the customer's back up data and reset the passwords.
16. Delete the customer's data from the SD Memory Card or from the PC to maintain security of the 

machine.

Содержание Workio DP-C265

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Workio DP-C265

Panasonic KX-P8415 Setup And Reference Manual preview
KX-P8415
Бренд: Panasonic Страницы: 32
IBM RS/6000 44P Series 270 User Manual preview
RS/6000 44P Series 270
Бренд: IBM Страницы: 216
Oki MC160N User Manual preview
MC160N
Бренд: Oki Страницы: 268
Oki LE810DT Manual De L'Utilisateur preview
LE810DT
Бренд: Oki Страницы: 54
Oki LE810DT Guías Del Usuario Manual preview
LE810DT
Бренд: Oki Страницы: 54
Oki MB460MFP Manual Do Usuário preview
MB460MFP
Бренд: Oki Страницы: 202
Oki MB460MFP Manual De L'Utilisateur preview
MB460MFP
Бренд: Oki Страницы: 201
Oki ES2232a4 User Manual preview
ES2232a4
Бренд: Oki Страницы: 103
Oki ES3037 User Manual preview
ES3037
Бренд: Oki Страницы: 256
Oki B710dn Hardware Manual preview
B710dn
Бренд: Oki Страницы: 2
Oki B710dn Material Safety Data Sheet preview
B710dn
Бренд: Oki Страницы: 36
Oki B6500 Series Guia Del Usuario De Redes preview
B6500 Series
Бренд: Oki Страницы: 63
Oki B6500 Series Customer Support Information preview
B6500 Series
Бренд: Oki Страницы: 28
Oki B6500 Series Service Manual preview
B6500 Series
Бренд: Oki Страницы: 616
Oki B411d Safety Information Manual preview
B411d
Бренд: Oki Страницы: 32
Oki B411d User Manual preview
B411d
Бренд: Oki Страницы: 138
Oki Microline 320 Turbo D1 Brochure & Specs preview
Microline 320 Turbo D1
Бренд: Oki Страницы: 2
Oki ML320 Epson/IBM Safety & Warranty preview
ML320 Epson/IBM
Бренд: Oki Страницы: 32

Бренды по названию

Популярные бренды

Загрузить еще бренды