Panasonic WJ-FS28 Скачать руководство пользователя

Страница: 37 / 48

4. Adjustment Procedure

Refer to the Location of the Test Points and

Adjusting Controls on the page 41.

(1). SC Frequency Adjustment

Test Point:

TP101 (RA SC)

Main Board

TP201 (RB SC)

Main Board

TP301 (RC SC)

Main Board

Adjust:

CT101 (RA SC)

Main Board

CT201 (RB SC)

Main Board

CT301 (RC SC)

Main Board

Disconnect all input signals from the WJ-FS28.

Connect the Frequency Counter to TP101 and TP1

(GND).

Adjust CT101 to obtain 4.433618 MHz ± 5 Hz.

Change the connection of the Frequency Counter to

TP201 and TP1.

Adjust CT201 to obtain 4.433618 MHz ± 5 Hz.

Change the connection of the Frequency Counter to

TP301 and TP1.

Adjust CT301 to obtain 4.433618 MHz ± 5 Hz.

(2). 4fsc Frequency Adjustment

Test Point:

TP901 (4fsc)

Main Board

Adjust:

CT903 (4fsc)

Main Board

Connect the Frequency Counter to TP901 and TP3

(GND).

Adjust CT901 to obtain 17.734475 MHz ± 20 Hz.

(3). Encoder Section Adjustment

Test Point:

Recording Output Jack

Rear Panel

Adjust:

VR803 (BURST GAIN)

Main Board

VR804 (Y DIVIDER)

Main Board

Supply the Composite Sync signal to the Playback Input

Jack on the Rear Panel of the WJ-FS28.

Connect the terminated Oscilloscope with 75

Ω

to the

Recording Output Jack on the Rear Panel of the WJ-

FS28.

Press the QUAD button on the Front Panel of the WJ-

FS28.

Adjust VR803 so that the Burst signal level becomes 300

± 14 mV as shown in Fig. 4-1.

Adjust VR804 so that the Y Divider signal level becomes

700 ± 14 mV as shown in Fig. 4-1.

Confirm that the Sync signal level becomes 300 ± 30 mV

as shown in Fig. 4-1.

Fig. 4-1

(4). PLL HD Phase Adjustment

Test Point:

TP801 (RA HD)

Main Board

TP802 (RB HD)

Main Board

TP803 (RC HD)

Main Board

Recording Output Jack

Rear Panel

Adjust:

VR801 (RB HD)

Main Board

VR802 (RC HD)

Main Board

Supply the Ramp signal to the Camera Input Connectors

1, 2 and 3 on the Rear Panel of the WJ-FS28.

Press the CH1 button on the Front Panel.

Connect the CH1 of the Oscilloscope to TP801 and CH2

of the Oscilloscope to TP802.

Trigger the Oscilloscope at TP801.

Adjust VR801 so that the rising edge of the RB HD Pulse

becomes within 0 ± 30 ns from the rising edge of the RA

HD Pulse as shown in Fig. 4-2.

Change the CH2 of the Oscilloscope to TP803.

Adjust VR802 so that the rising edge of the RC HD Pulse

becomes 0 ± 30 ns from the rising edge of the RA HD

Pulse as shown in Fig. 4-2.

Note: If the waveform distortions are not same, adjust

around 2.5 V DC.

Fig. 4-2

Press the CH4 button on the Front Panel.

Supply the Crosshatch signal to the Camera Input

Connectors 1, 2 and 3.

700 ± 14 mV

300 ± 30 mV

300 ± 14 mV

TP801

TP802
TP803

Reference

2.5 V DC

= within ± 30 ns.

Note : If the waveform distortions are not same,

adjust around 2.5 V DC.

Содержание WJ-FS28

















































Результаты поиска

Содержание WJ-FS28

Отзывы:

Похожие инструкции для WJ-FS28

Бренды по названию

Популярные бренды

Panasonic WJ-FS28, Руководство по обслуживанию

Результаты поиска

Содержание WJ-FS28

Отзывы:

Похожие инструкции для WJ-FS28

Бренды по названию

Популярные бренды