background image

Installation Guide

Model Name

Video Intercom System

Main Monitor Station

Model No.

VL-SVN511 Series

VL-MVN511

R

This guide is for use with the above 2 models.

R

The VL-SVN511 models composition consists of VL-MVN511 and VL-V522L.

VL-V522L

VL-MVN511

Door station

Main monitor station

R

The Installation Guide in Indonesian and Thai can be accessed from the following site:
http://panasonic.net/pcc/support/intercom/svn511/

R

Door station is described as "doorphone" and Main monitor station is described as "main
monitor" in this guide.

R

In this guide, the suffix of each model number (e.g., the "BX" in "VL-SVN511BX") is omitted
unless necessary.

Note to the installer

R

Before attempting to connect or operate this product, please read the label on the rear of
the doorphone and the main monitor.

R

Please read this guide carefully, and install the product safely and correctly by following
the instructions. Carefully read the information found in the section titled "For your
safety" in particular.

R

Only use attachments/accessories specified by the manufacturer.

R

The installation shall be carried out in accordance with all applicable installation rules.

R

Panasonic assumes no responsibility for injuries or property damage resulting from
failures arising out of improper installation or operation inconsistent with this guide.
Additionally, any resulting malfunction will not be covered under the warranty.

R

After installation, make sure to leave this guide with the customer.

Содержание VL-SVN511 Series

















Отзывы: