31
10 Disassembly and Assembly Instructions
Caution Note:
• This section describes the disassembly and/or assembly procedures for all major printed circuit boards & main compo-
nents for the unit. (You may refer to the section of “Main components and P.C.B Locations” as described in the service
manual)
• Before carrying out the disassembly process, please ensure all the safety precautions & procedures are followed.
• During the disassembly and/or assembly process, please handle with care as there may be chassis components with
sharp edges.
• Avoid touching heatsinks due to its high temperature after prolong use. (See caution as described below)
• During disassembly and assembly, please ensure proper service tools, equipments or jigs is being used.
• During replacement of component parts, please refer to the section of “Replacement Parts List” as described in the
service manual.
• Select items from the following indexes when disassembly or replacement are required.
Main Unit (SU-ZT2)
• Disassembly of Top Cabinet
• Disassembly of HDMI P.C.B.
• Disassembly of DSP P.C.B.
• Disassembly of Rear Panel
• Disassembly of Wireless TX P.C.B. and TX Module P.C.B.
• Disassembly of Main P.C.B.
• Disassembly of Front Cabinet
• Disassembly of Panel P.C.B. and Power SW P.C.B.
Speaker Unit (SB-ZT2)
• Disassembly of Woofer Block
• Disassembly of Middle Cabinet Assembly
• Disassembly of Extent P.C.B.
• Disassembly of SMPS P.C.B. and AC Inlet P.C.B.
• Replacement of IC5701
• Replacement of Diode (D5802)
• Disassembly of D-Amp P.C.B.
• Disassembly of RX Module P.C.B.
• Disassembly of Input P.C.B.
• Disassembly of Port Assembly (A , B) and Port Assembly (C, D)
• Disassembly of Woofer Speaker (SP1)
• Disassembly of Arm Unit
• Disassembly of Prepared Net Assembly
• Disassembly of Antenna Cover Assembly
• Disassembly of Antenna Wire
• Disassembly of Tweeter Speakers (SP2 / SP3 / SP4 / SP5)
Содержание VIERA Link SB-ZT2EE
