background image

12

6.2.

Option - Mirror

Picture can be reversed left and right or up and down.
00 : Default (Normal picture is displayed)
01 : Picture is reversed left and right.
02 : Picture is reversed up and down.

Hint : If the defective symptom (e.g. Vertical bar or Horizontal bar) is moved by selection of this mirror, the possible cause is in 
A-board. 

6.3.

Service tool mode

6.3.1.

How to access 

1. Select [SRV-TOOL] in Service Mode.
2. Press [OK] button on the remote control.

6.3.2.

Display of SOS History

SOS History (Number of LED blinking) indication.
From left side; Last SOS, before Last, three occurrence before, 2nd occurrence after shipment, 1st occurrence after shipment.
This indication will be cleared by [Self-check indication and forced to factory shipment setting].

6.3.3.

POWER ON Time, On/Off

Note : To display TIME/COUNT menu, highlight position, then press MUTE for 3 sec.
Time : Cumulative power on time, indicated hour : minute by decimal
On/Off : Number of On/Off switching by decimal
Note : This indication will not be cleared by either of the self-checks or any other command.

6.3.4.

Exit

Disconnect the AC cord from wall outlet or switch off the power with [ Power ] button on the main unit.

Содержание TX-P42GT60B





































Отзывы: